How do I turn on cruise control on my 2018 Chevy Equinox?
Cruise control is a convenient feature that allows you to maintain a consistent speed while driving, reducing fatigue and improving fuel efficiency. If you own a 2018 Chevy Equinox, you can easily activate the cruise control system to make your driving experience more comfortable and efficient.
Locating the Cruise Control Buttons
The cruise control buttons on your 2018 Chevy Equinox are typically located on the steering wheel or the turn signal stalk. Look for the following buttons:
- On/Off Button: This button turns the cruise control system on and off.
- Set/Resume Button: This button sets the current speed as the cruise control speed or resumes the previously set speed.
- Cancel Button: This button temporarily disables the cruise control without turning the system off.
Once you've identified the cruise control buttons, you're ready to start using the feature.
Activating Cruise Control
To turn on the cruise control in your 2018 Chevy Equinox, follow these steps:
- Ensure the cruise control system is turned on by pressing the On/Off button.
- Accelerate your vehicle to the desired speed.
- Press the Set/Resume button to set the current speed as the cruise control speed.
- The cruise control indicator light on your dashboard will illuminate, indicating that the system is active.
To adjust the set speed, simply press the Set/Resume button to increase the speed or tap the brake pedal to temporarily disengage the cruise control. You can then press the Set/Resume button again to resume the previously set speed.
Disabling Cruise Control
To turn off the cruise control system, you can either press the Cancel button or tap the brake pedal. This will disengage the cruise control without turning the system off. If you want to completely turn off the cruise control, press the On/Off button.
Remember, it's important to use cruise control responsibly and always maintain control of your vehicle, especially in adverse weather conditions or heavy traffic.
Why is my cruise control not setting?
Any issues with your car's electrical components can cause the cruise control to stop working. These issues could be something as simple as a loose wire or connector, or something more complicated like a damaged alternator, starter, or electrical short circuit.
How to set cruise control on 2018 Chevy Equinox?
To engage Cruise Control in your Chevy, first locate the Cruise Control button, usually on the steering wheel. Once you're at your desired speed, simply press the button to activate the system. Once activated, the car will hold that speed.
Why is the cruise control not working on my Chevy Equinox?
The most common reasons a Chevrolet Equinox cruise control isn't working are failed control module, sensor or switch issues, or throttle actuation problems.
Where is my cruise control button?
Typically, the cruise control buttons can be found on the right-hand side of the steering wheel. Depending on the car, the location of the controls can vary, but the functionality of the cruise control will usually be similar across the board. Here are the basic buttons you can use to operate cruise control.
What is the cruise control symbol on the dashboard?
The cruise control system will often be a speedometer symbol with an arrow pointing to a set speed. It will light up green when it has been successfully set, and an amber or yellow light can indicate that cruise control is enabled but not set, or that there is a problem with the system.
Why does my car say cruise control unavailable?
It's possible for a cruise control switch to wear out over time by being pressed too much or too hard. It may also get damaged by drink spillages or by solvent used when cleaning the steering wheel. This could mean the CCM cannot be communicated with, potentially disabling cruise control entirely.
Why can't I turn on my cruise control?
Any issues with your car's electrical components can cause the cruise control to stop working. These issues could be something as simple as a loose wire or connector, or something more complicated like a damaged alternator, starter, or electrical short circuit.
How to use Chevy cruise control?
You turn on adaptive cruise. Simply select the set cruise control button. And select the speed you want to go we will then adapt to the person in front of you. So I have it set at 51.
How do I activate cruise control?
To use cruise control, you can typically press buttons on your steering wheel to activate the system, set your speed, adjust your speed up or down within the system, and deactivate the system. Using cruise control lets you set a speed for your car to maintain even if you take your foot off the gas.
How do I fix cruise control not turning on?
Since your car's cruise control is part of an electrical system, it needs a fuse to function properly. A short circuit in this system can cause a fuse to blow, which means that the cruise control will suddenly stop working. Fortunately, replacing a blown fuse is a cheap and easy repair for any auto mechanic.
