How do you reset the parking brake on a Honda HRV?

There isn’t a simple consumer reset button for the Honda HR‑V’s electronic parking brake. If the system is behaving oddly or a warning light is on, a Honda dealer or certified shop will typically need to recalibrate it with specialized diagnostic tools.

Understanding the HR‑V’s electronic parking brake

The HR‑V uses an electronic parking brake (EPB) with auto‑hold, instead of a traditional manual handbrake. A small switch labeled P engages or releases the brake, and sensors monitor wheel movement and pedal input. After events like a battery disconnect or certain faults, the system may require recalibration or software updates at a service center.

What you should know about attempting a reset at home

Below are points to consider if you’re dealing with a minor glitch or want to try a non‑professional refresh. These steps are not a guaranteed fix and should not replace professional service for warning lights or when the brake won’t release.

• Ensure the vehicle is on a flat surface and the ignition is in the ON position (engine off or as recommended by your owner’s manual).


• Firmly apply the foot brake, then operate the EPB switch to engage and release the brake as a circuit refresh, repeating once or twice if the system seems to re‑sync.


• Check the 12‑V battery health and charging system; a weak or failing battery can affect EPB calibration and operation.


• Look for any warning messages on the instrument cluster and, if you have access to an OBD‑II scanner, note any EPB‑related fault codes for service guidance.

These steps are intended to address occasional glitches and may help your system recover from minor irregularities. If the problem persists, professional assessment is advised.

When to seek professional service

Because the EPB is a safety‑critical component, persistent faults or failure to release should be treated as a service issue. A Honda technician with the proper diagnostic tools can perform a formal recalibration or software update if needed. Consider service if any of the following apply:

• The parking brake warning light stays on or flashes after attempting a reset.


• The brake fails to release or the vehicle cannot be moved safely.


• You recently had a battery replacement or electrical work and the EPB does not recalibrate.


• You hear abnormal noises from the rear brakes when engaging or releasing the EPB.

A dealer or qualified shop can perform the EPB calibration using Honda’s service tooling and apply any necessary software updates to ensure proper operation.

Summary

In short, the Honda HR‑V’s electronic parking brake does not offer a simple, user‑initiated reset. Minor glitches can sometimes be refreshed through a basic cycle and system checks, but any persistent fault or failure to release requires professional calibration with factory tools. Regular maintenance and prompt attention to warning indicators help keep the EPB functioning safely.

If you’re unsure or the warning persists, contact your local Honda service center or roadside assistance for guidance and safe resolution.

How to fix an electric parking brake problem?

To fix an electric parking brake (EPB) problem, try a simple reset by disconnecting the car's battery or using the vehicle's specific reset procedure. If a reset doesn't work, inspect and repair any loose or damaged electrical connections, or consult a mechanic for issues like a faulty actuator, switch, or wiring. For an emergency release, look for an override lever, which can be found in the owner's manual. 
Initial troubleshooting and resets

• Perform a system reset: This can fix minor software glitches. 
  • Disconnect the negative terminal of the car battery for a few minutes, then reconnect it to restart the system. 
  • Alternatively, follow the vehicle-specific reset procedure in your owner's manual, which often involves pressing the parking brake switch in a specific sequence. A common method is to hold the parking brake switch on, then off, while the car is on and the brake pedal is pressed. 
• Check fuses: A blown fuse can cause the EPB to malfunction. Consult your owner's manual to locate and inspect the relevant fuse. 

This video demonstrates a common procedure to reset the electronic parking brake: 1mWeeklyToolsYouTube · Jul 6, 2023
Advanced troubleshooting

• Inspect electrical connections: Check all wiring harnesses and connectors for any signs of damage, loose connections, or corrosion and repair them as needed. 
• Diagnose faulty components: A persistent issue could be a faulty electronic control unit (ECU), parking brake switch, or actuator. These may require professional diagnosis. 
• Bypass a stuck EPB: If you need to move the car immediately, you may be able to manually release the EPB. 
  • Find the emergency release cable or lever, often located near the rear of the center console or near the left rear taillight. 
  • Use a screwdriver or pliers to pull the cable until the brake releases. You may need a second person to help release the brake. 

When to seek professional help

• If the warning light remains on after trying a reset, it indicates a more significant problem that requires a professional diagnosis. 
• Faulty components like the actuator are common but may require specialized tools or expertise to replace. 
• For safety, do not drive the vehicle if the parking brake warning light is still on, as it can affect the brake system's lifespan. 

How to reset Honda parking brake?

To reset a Honda's electronic parking brake, use a diagnostic scan tool for the most reliable method, especially after brake maintenance. A manual reset is possible by turning the ignition to the "ON" position (without starting the engine) and repeatedly pulling and holding the parking brake switch until the light flashes, then pressing it again. 
Method 1: Using a scan tool
This is the recommended method, particularly after replacing brake pads, to put the system in service mode and then return it to normal mode. 

1. Connect the scan tool to the vehicle's OBD-II port.
2. Navigate to the vehicle's anti-lock brake system (ABS) or electronic parking brake (EPB) module. 
3. Find and select the "Brake Pad Maintenance" or "Service" mode option. 
4. Follow the on-screen prompts to enter service mode. 
5. After completing maintenance, use the scan tool again to select the option to "Return to Normal Mode". 

This video demonstrates how to use a scan tool to put the Honda parking brake into maintenance mode: 1mT. M. G. GarageYouTube · May 11, 2024
Method 2: Manual reset (for basic issues)
This method may reset the system after minor malfunctions. 

1. Turn the ignition to the "ON" position without starting the engine.
2. Depress and hold the brake pedal.
3. Pull and hold the parking brake switch for about 5 seconds, until the parking light on the dashboard starts to flash.
4. Release the switch, then quickly press and release it again.
5. Release the brake pedal.

Method 3: Disconnecting the battery (use with caution) 
This is a last resort and may cause other systems to lose their settings, requiring you to re-enter them. 

1. Disconnect the positive (+) battery terminal. 
2. Wait for at least 10 minutes. 
3. Reconnect the battery terminal. 
4. Restart the car to allow the system to recalibrate. You may need to re-pair your phone and reset the clock and radio presets. 

You can watch this video to see how to reset the parking brake by disconnecting the battery: 59sMaxTheCarGuyYouTube · May 5, 2023
Important considerations

• Consult your owner's manual: for the specific reset procedure for your model year, as steps can vary.
• Safety first: Ensure the vehicle is in a safe and stable location before attempting any of these procedures. 
• Professional help: If the issue persists, it's best to consult a Honda dealership or a qualified mechanic for diagnosis and repair. 

How do you reset the electronic parking brake on a Honda HRV?

Step. Press and hold down the electronic parking brake control button or switch keep it pressed for about 10 to 15 seconds. This step is crucial as it initiate while holding down the control observe

How do you reset the parking sensor on a Honda HRV?

Press and hold the parking sensor system button, and set the power mode to ON. 3. Keep pressing the button for 10 seconds. Release the button when the indicator in the button flashes.