Loading

How many gallons of coolant does a 2013 Ford Escape take?

In general, the 2013 Ford Escape coolant system holds about 2 gallons of antifreeze and water mix, but the exact amount varies by engine configuration. Most engines fall roughly in the 1.9 to 2.6 gallon range, depending on the model and whether you count the entire cooling system. For a precise figure, consult the owner's manual or Ford service data for your specific engine.


Engine options and cooling capacity


Before listing specific figures, note that coolant capacity depends on the engine and components included in the calculation. The following are approximate ranges based on typical specifications for 2013 Escapes.



  • 2.5-liter inline-4 (I-4): about 7.5–9.0 quarts (1.9–2.3 gallons)

  • 1.6-liter EcoBoost: about 7.0–8.0 quarts (1.75–2.0 gallons)

  • 2.0-liter EcoBoost: about 9.0–10.5 quarts (2.25–2.6 gallons)

  • Hybrid version (2.5-liter Atkinson-cycle): about 10–11 quarts (2.5–2.75 gallons)


Concluding note: The exact capacity can differ based on whether you include coolant in the radiator, heater core, engine block, and reservoir. Check the vehicle’s manual or Ford service data for the precise specification for your VIN.


Practical guidance


When planning a coolant replacement or refill, aim for a 50/50 mix of antifreeze and distilled water unless local climate guidelines advise a different ratio. After draining, fill through the reservoir and bleed the system by running the engine with the cap off until bubbles subside, then top up to the correct level.


Summary


The 2013 Ford Escape generally requires around 2 gallons of coolant, with engine-specific variations typically placing capacity in the 1.9–2.6 gallon range. For the exact amount for your vehicle, refer to the owner’s manual or Ford service data for your engine and VIN.

What coolant do I need for a 2013 Ford Escape?


The 2013 Ford Escape uses an orange, Phosphated Hybrid OAT (P-HOAT) coolant that is compatible with Dex-Cool specifications. You can use either a 50/50 pre-mixed version or the concentrated version and mix it yourself with distilled water. It's important to verify the coolant type and color in your owner's manual before adding any new fluid, and never mix different types of coolant. 
This video demonstrates how to check the coolant fluid in a Ford Escape: 1mPeter Finn the Car DoctorYouTube · Dec 9, 2013

  • Coolant Type: The correct coolant is a Ford-specified orange, P-HOAT formula, similar to Dex-Cool. 
  • Options:
    • 50/50 Pre-mixed: This is a ready-to-use option that is convenient for top-offs or full flushes. 
    • Concentrate: You can buy the concentrated version and mix it yourself with distilled water. 
  • Important Note: Always check your owner's manual or the coolant reservoir itself to confirm the correct type and color before adding any new fluid. Do not mix different types of coolant. 



How many gallons of coolant do I need?


You will likely need between 1 and 2 gallons of coolant concentrate to mix with an equal amount of distilled water for a 50/50 solution, but the exact amount depends on your vehicle's cooling system capacity, which can range from 3 to 7 liters (or about 0.75 to 1.75 gallons). It is best to consult your owner's manual or purchase a slightly larger quantity, such as two gallons of concentrate, to ensure you have enough, as some systems can hold more and you may need extra to top off. 
How to determine the right amount

  • Check the owner's manual: This is the most reliable method, as it will state the exact capacity of your vehicle's cooling system. Look for information under "fluid capacities". 
  • Estimate based on engine size: If you don't have the manual, you can estimate that 4-cylinder engines generally require between 1 and 2 gallons of a 50/50 mix. Larger engines will need more. 
  • For a complete flush: If you are doing a full coolant flush, you will likely need more concentrated antifreeze. You can start by adding about 4 gallons of concentrate to a system that holds 8 gallons total, as you can't drain all the old coolant, and then fill the rest with distilled water. 
  • For topping off: If you are just topping off the system, add enough to reach the "COLD" line on the overflow tank. The amount will be much smaller, likely less than a quart, says this Quora post. 

Important tips
  • Always use distilled water: Never use tap water, as the minerals can cause corrosion in your cooling system. 
  • Mix it correctly: Make sure to mix the antifreeze with distilled water in a 50/50 ratio for optimal protection. 
  • Check the level after service: After refilling, run the engine and keep an eye on the coolant level, as air bubbles may need to be "burped" out of the system. 



How many gallons does a Ford Escape 2013 hold?


The 2013 Ford Escape has a fuel tank capacity of 15.1 gallons for the standard models. Some sources may list a slightly different size, such as 15.7 gallons for the 2.0L engine, but 15.1 gallons is the most commonly cited size for most trims.
 

  • 15.1 gallons: This is the standard fuel tank capacity for most 2013 Ford Escape models, including the SE and Titanium trims with the 2.5L or 1.6L engines, according to U.S. News & World Report, Edmunds, and Edmunds. 
  • 15.7 gallons: Some sources report a 15.7-gallon tank for the 2.0L engine, notes Five Star Ford Stone Mountain. It is always best to double-check your owner's manual for the most accurate information for your specific vehicle. 



How many quarts does a 2013 Ford Escape take?


A 2013 Ford Escape takes 5.7 quarts of oil for the 2.5L and 2.0L engines, while the 1.6L engine takes 4.1 quarts. Always check the owner's manual for the most accurate capacity for your specific engine and check the oil level after refilling to ensure it's correct. 
Engine oil capacities

Engine Size Oil Capacity (with filter)
1.6L 4.1 quarts
2.0L 5.7 quarts
2.5L 5.7 quarts
(function(){
(this||self).Wufxzb=function(c,e,f,l,k){var d=document.getElementById(c);if(d&&(d.offsetWidth!==0||d.offsetHeight!==0)){c=d.querySelector("div");var g=c.scrollWidth-c.offsetWidth,h=Math.min(e?g:0,g);c.scrollLeft=e&&(l||f)?0:h;var a=d.getElementsByTagName("g-left-button")[0],b=d.getElementsByTagName("g-right-button")[0];a&&b&&(e=RegExp("\\btHT0l\\b"),f=RegExp("\\bpQXcHc\\b"),a.className=a.className.replace(e,""),b.className=b.className.replace(e,""),h===0?a.className="pQXcHc "+a.className:(a.className=
a.className.replace(f,""),k&&c.classList.add("pA30Ne")),h===g?b.className="pQXcHc "+b.className:(b.className=b.className.replace(f,""),k&&c.classList.add("FpCCub")),setTimeout(function(){a.className+=" tHT0l";b.className+=" tHT0l"},50))}};}).call(this);(function(){var id='_Yt0laeqaBPON9u8PzefL2QE_252';var rtl=false;var gecko=false;var edge=false;var soh=false;
(this||self).Wufxzb(id,rtl,gecko,edge,soh);})();


Kevin's Auto

Kevin Bennett

Company Owner

Kevin Bennet is the founder and owner of Kevin's Autos, a leading automotive service provider in Australia. With a deep commitment to customer satisfaction and years of industry expertise, Kevin uses his blog to answer the most common questions posed by his customers. From maintenance tips to troubleshooting advice, Kevin's articles are designed to empower drivers with the knowledge they need to keep their vehicles running smoothly and safely.