How many quarts does a 2008 Ford Taurus take?
The 2008 Ford Taurus typically takes about 5 quarts of engine oil with a filter, though the exact amount depends on the engine variant. Most configurations fall in the 4.5–5.0 quart range, so always verify with the owner's manual or under‑hood label for your specific engine.
Engine options and capacities
In 2008, the Taurus used two main V6 engine families. Oil capacity differs by engine type, so the following figures are guidelines you can use when planning an oil change.
- 3.0-liter Vulcan V6: about 4.5 quarts of engine oil with a filter
- 3.0-liter Duratec V6 (a later variant used in some Taurus models): about 5.0 quarts of engine oil with a filter
Bottom line: plan for roughly 4.5–5 quarts of oil when changing the oil on a 2008 Taurus, and always top up to the correct level after the engine has run and cooled.
Practical tips for changing oil on a 2008 Taurus
When performing an oil change, drain oil completely, replace the oil filter, and begin by adding a little less than the full capacity. Start the engine, run for a few minutes, then turn off and let it settle. Re-check the dipstick and top off in small increments until the level sits within the full range specified by the dipstick.
Summary
For a 2008 Ford Taurus, expect an oil capacity of roughly 4.5–5 quarts depending on the engine variant. Verify the exact capacity for your car using the owner's manual or the vehicle's service label, and always confirm oil level with the dipstick after an oil change.
How much oil does a 3.5 Ford Taurus take?
The oil capacity for a Ford Taurus with a 3.5L engine is typically 6 quarts (5.7 L) when the filter is changed, though some model years may be slightly different. The correct oil viscosity is also crucial; 5W-20 is a common recommendation, but you should always check your owner's manual for the exact requirements for your vehicle's specific year and trim.
Ford Taurus 3.5L oil capacity
- Capacity: 6 quarts (5.7 L) with a filter change
- Viscosity: 5W-20 is a common recommendation for most models, but always check your owner's manual to confirm the correct viscosity for your specific year and engine type.
- After refilling: Always check the oil level with the dipstick to ensure it's correct.
How many quarts of oil does a Ford Taurus take?
A Ford Taurus takes between 4.5 and 6 quarts of oil, depending on the model year and engine size. For example, a 3.0L V6 engine requires about 4.5 quarts, while larger 3.5L and 6-cylinder engines typically need 6 quarts. Always check your owner's manual to confirm the exact capacity for your specific vehicle before adding oil.
- 4.5 quarts: Some older 3.0L V6 engines, such as in a 1999 model, need approximately 4.5 quarts.
- 6 quarts: Many newer 3.5L V6 engines, including those found in models from 2010 to 2019, require 6 quarts of oil when the filter is changed.
- Always check: It is best to consult your vehicle's owner's manual or the sticker under the hood for the most accurate oil capacity for your specific year and engine.
How many quarts of oil does a 2008 Ford Taurus take?
The 2008 Ford Taurus with the 3.5L engine has an oil capacity of 5.5 quarts (5.2 liters) when changing the oil and filter. It is important to use a 5W-20 viscosity oil and to check the oil level on the dipstick after refilling.
- Capacity: 5.5 quarts (5.2 liters) with an oil filter change.
- Oil Type: 5W-20 viscosity.
- Procedure: Change the filter when you change the oil and check the level on the dipstick after you are finished.
How many quarts of oil does a 3.5 L V6 engine take?
6.0 qt
Capacities and Specifications - 3.5L Ecoboost
| Item | Capacity |
|---|---|
| Engine oil (with oil filter) | 5.7 L (6.0 qt) |
| Engine coolant | 12.4 L (13.1 qt) |
| Brake fluid | Between MIN/MAX on brake fluid reservoir |
| Rear axle fluid (four-wheel drive) | 2.11 pt (1.0 L) |
