How many quarts does a 2010 Dodge Nitro take?
The 2010 Dodge Nitro takes 5 quarts of oil for a standard oil change. This information is based on the vehicle's owner's manual and technical specifications.
Detailed Answer
The 2010 Dodge Nitro is a mid-size SUV that was produced by Dodge from 2007 to 2012. When it comes to the oil capacity, the 2010 model year Nitro requires 5 quarts of oil for a standard oil change.
This information can be found in the owner's manual for the 2010 Dodge Nitro, as well as in the technical specifications provided by the manufacturer. The oil capacity is an important detail to know when performing routine maintenance on the vehicle.
Oil Change Procedure
To change the oil in a 2010 Dodge Nitro, you will need the following:
- 5 quarts of the recommended motor oil (check owner's manual for specifications)
- Oil filter
- Oil drain pan
- Wrenches and tools to access the oil drain plug and filter
The basic steps for changing the oil in a 2010 Dodge Nitro are:
- Park the vehicle on a level surface and apply the parking brake.
- Locate the oil drain plug, usually on the bottom of the oil pan, and place the drain pan underneath.
- Using a wrench, loosen and remove the drain plug to allow the old oil to drain out.
- Once the oil has fully drained, replace the drain plug and tighten it back up.
- Locate the oil filter, usually accessible from the top of the engine, and use a filter wrench to remove it.
- Apply a thin coat of new oil to the gasket of the new filter, then screw on the new filter by hand until secure.
- Unscrew the oil fill cap and pour in 5 quarts of the recommended motor oil.
- Replace the oil fill cap and start the engine to circulate the new oil.
- Check the oil level using the dipstick and add more oil if necessary to reach the full mark.
Be sure to dispose of the old oil and filter properly, and always refer to the owner's manual for the specific oil change procedure and recommendations for your 2010 Dodge Nitro.
How much oil does a Dodge Nitro 3.7 take?
5.0 qt.
Engine Speed 6000 rpm (electronically limited) Fuel Requirement Unleaded regular, 87 octane Oil Capacity 3.7 L (5.0 qt.) Coolant Capacity 13.25 L (14.0 qt.)
How much oil does a 4.0 Dodge Nitro take?
6 quarts
Capacity: 6 quarts (with filter).
How many quarts does a 4.0 take?
6 quarts (with filter). After refill check oil level.
What kind of oil does a 2010 Dodge Nitro take?
Oil Grade: SEO11
| Viscosity: | 5W-20 (All TEMPS) |
|---|---|
| Capacity: | 5 quarts (with filter). After refill check oil level. |
| Torque: | 25 ft/lbs (Oil Drain Plug) |
How much oil does a 2.8 L engine take?
4.5 Qt
Customer: how much oil does a 2.8 v6 take for an oil and filter chane? GM Grand Master Technician 2007. 14 years experience. WelcomeCustomer The approximate oil capacity for an oil change with the filter is 4.3L or 4.5 Qt of 5w30 oil.
How many quarts does a 3.7 Dodge take?
Capacities and Specifications - 3.7L
| Item | Capacity |
|---|---|
| Engine oil (with oil filter) | 6.0 qt (5.7 L) |
| Engine coolant | 11.7 qt (11.1 L) |
| Brake fluid | Between MIN/MAX on brake fluid reservoir |
| Rear differential fluid (All Wheel Drive) | 2.4 pt (1.15L) |
How much oil does a Dodge Nitro 2.8 take?
6.6 L
Your DODGE NITRO 2.8 CRD 4WD will take 6.6 L for a full oil change.
How big is a Dodge Nitro gas tank?
19.5 gal
Fuel & MPG
312.0/429.0 mi. 19.5 gal.
What kind of oil does a Dodge Nitro need?
AMSOIL OE 5W-20 100% Synthetic Motor Oil.
How many gallons does a 2010 Dodge Nitro hold?
19.5 gal
