How many quarts does a 3.5 Ford Edge take?
The 3.5L Ford Edge typically takes about 5.7 quarts of engine oil when changing the oil with a new filter.
Oil capacity can vary by model year and whether you include the oil filter in the calculation. This article outlines the typical figure for the Duratec 35 engine used in many Edge models and explains how to verify the exact amount for your vehicle.
Typical oil capacity for the 3.5L Edge
Before listing the figures, note that capacities are most commonly cited for the Duratec 35 V6 used in many Ford Edge models (roughly 2011–2018). Exact numbers can vary slightly by year or by any factory changes, so use these as a guide and confirm with your manual or dealer if in doubt.
Here are the typical oil capacity figures you can expect when performing an oil change on a 3.5L Edge:
- Capacity with a fresh oil filter: 5.7 quarts (approximately 5.4 liters)
- Capacity without the filter: about 5.0 quarts (approximately 4.8 liters)
In practice, start by adding about 5.7 quarts, then run the engine, check the level with the dipstick when the oil is warm, and top off cautiously if needed to reach the full mark.
Oil type, maintenance tips, and checks
Choosing the right oil and following proper check procedures helps ensure the engine stays protected and the level reads accurately on the dipstick.
- Recommended oil: typically 5W-20 full synthetic or synthetic blend, unless your manual specifies a different grade.
- Oil filter: replace with every oil change to preserve capacity accuracy and filtration efficiency.
- Check procedure: run the engine briefly, shut off, wait a few minutes for oil to settle, then check the dipstick to confirm you’re at the full mark when warm.
- Variations by year: some model years or engine updates can adjust capacity slightly; always verify against your owner’s manual or Ford service data.
If you’re unsure about your exact year or engine variant, contact a Ford dealership or consult the official manual for your specific VIN to confirm the precise capacity and oil specification.
Notes on verification and best practices
For the most accurate result, always confirm with the vehicle’s documentation. A quick dipstick check after the engine has run and rested will tell you if you need to add or remove a small amount to reach the full level.
Summary
Bottom line: The 3.5L Duratec Edge typically requires about 5.7 quarts of oil with the filter installed, with roughly 5.0 quarts if you exclude the filter. Use the recommended 5W-20 oil, replace the filter at every oil change, and verify the final level with the dipstick after warming up the engine. When in doubt, consult the owner’s manual or a Ford dealer for your exact year and VIN.
How much oil does a 2012 Ford Edge 3.5 take?
The 2012 Ford Edge 3.5L engine has an oil capacity of 6.0 quarts (5.7 liters) when the filter is changed. It is important to check the dipstick after refilling to ensure the correct level is reached.
- Capacity: 6.0 quarts (5.7 liters) with a filter change.
- Oil Type: The recommended oil is 5W-20.
- Checking the level: After the oil is added, start the engine briefly, then turn it off and wait a few minutes. Check the dipstick and add more oil if necessary to reach the correct level.
How much oil does a 3.5 l V6 Ford Edge take?
The oil capacity for a Ford Edge with a 3.5L engine is typically 6 quarts (5.7 L) when changing the filter, though some earlier models may require slightly less, such as 5.5 quarts. Always check the dipstick after refilling and top off as needed to ensure the correct level.
- For most models: The capacity is around 6 quarts (5.7 L) when changing the oil and filter.
- For some earlier models: The capacity may be closer to 5.5 quarts.
- After filling: Check the oil level with the dipstick and add more oil if necessary until it reaches the proper mark.
What oil does a 2013 Ford Edge 3.5 L take?
Full Synthetic Motorcraft Engine Oil Change Kit for 2013 Ford Edge 3.5L V6 5w20.
What kind of oil does a 2017 Ford Edge 3.5 take?
The correct oil for a 2017 Ford Edge 3.5L is SAE 5W-20, and it should meet the Ford WSS-M2C945-A specification,. The vehicle takes about 6 quarts of oil when the filter is changed, but you should always check your owner's manual for the exact capacity and specifications for your specific model. You can use either a full synthetic or a synthetic blend motor oil.
- Oil type: SAE 5W-20
- Specification: WSS-M2C945-A
- Capacity: Approximately 6 quarts with filter change
- Consistency: Full synthetic or synthetic blend
Important considerations:
- For extremely cold climates where temperatures drop below -22∘Fnegative 22 raised to the composed with power cap F−22∘𝐹 (-30∘Cnegative 30 raised to the composed with power cap C−30∘𝐶), you can use 0W-20 oil that meets the WSS-M2C945-A specification.
- Always check your owner's manual to confirm the exact oil specification and capacity for your vehicle.
