How many quarts of transmission fluid goes in a Chrysler 300?

The exact amount depends on the model year, transmission type, and whether you’re doing a simple drain-and-fill or a full flush. In general, expect about 11–13 quarts for a full service, with drain-and-fill typically using about 6–9 quarts.

Over the years, the Chrysler 300 has used several automatic transmissions, each with its own capacity. For a precise figure, consult the vehicle’s owner's manual or the factory service manual for your specific VIN and transmission code, or check with an authorized dealer.

Common transmission options and their approximate capacities

The ranges below reflect typical configurations found in Chrysler 300 models across different generations. Use them as a rough guide and verify against your exact build.

• Older 4-speed automatics (41TE/related family): total capacity roughly 11–12 quarts; a standard drain-and-fill usually around 6–9 quarts.


• Modern 5-speed automatics (545RFE/related family): total capacity around 12–13 quarts; drain-and-fill typically 7–9 quarts; a full flush can require 12–14 quarts.

Remember that exact figures depend on the transmission code, torque converter, and whether you are performing a simple pan drain or a full fluid change including lines and the torque converter.

How to determine the exact capacity for your Chrysler 300

To nail down the precise fluid capacity for your car, follow these steps:

1. Identify your transmission type and code from the owner's manual, service manual, or by VIN decoding.


2. Check the official Chrysler service documentation or the dealership's service portal for the exact capacity and fluid specification for that code.


3. Measure how much fluid you drain during a pan drain and fill, then refill to the recommended level using the correct fluid type (ATF+4 or Dexron-type as specified).


4. Consider whether you’re performing a drain-and-fill or a complete flush (which includes the torque converter) and adjust the fluid amount accordingly.


5. Record the total amount added and verify the level after a short drive, ensuring it remains within the specified range.

Because the exact figure can vary by VIN and transmission code, the most reliable source is the factory documentation or a dealership service bulletin for your specific Chrysler 300.

Summary

There isn’t a single universal number for the Chrysler 300. Most automatic transmissions in this model require roughly 11–13 quarts for a full service, with a standard drain-and-fill using about 6–9 quarts. For precision, identify your transmission code and consult the official service documentation or a dealer, and always use the fluid type specified by the manufacturer.

How many quarts does a 3.6 Chrysler 300 take?

Below as well the V6. In this 300 requires 5.9 quarts of oil. So first we're going to fill it with 5 quarts. Then we're going to start the car. And make sure that the oil gets primed into the filter.

How many quarts of transmission fluid does a Chrysler 300 take?

The transmission fluid capacity for a Chrysler 300 depends on the year and transmission type. For older 5-speed NAG1 transmissions, the total capacity is around 8.1 quarts, with an initial fill of 5.3 quarts. For newer 8-speed transmissions, the dry fill capacity is 8.3 to 9.2 liters (about 8.8 to 9.7 quarts), while a drain and refill is about 4.5 to 5.0 liters (about 4.8 to 5.3 quarts). 
This video demonstrates the process of changing transmission fluid in a Chrysler 300 with a ZF 8-speed transmission: 38sTyler PotterYouTube · Aug 19, 2024
5-Speed NAG1 Transmission

• Total Fill Capacity: 8.1 quarts
• Initial Fill Capacity: 5.3 quarts 

8-Speed Transmission (2012-2023)

• Dry Fill Capacity: 8.3 to 9.2 liters (approximately 8.8 to 9.7 quarts)
• Drain and Filter Change Capacity: 5.5 to 6.0 liters (approximately 5.8 to 6.3 quarts)
• Drain and Refill Capacity: 4.5 to 5.0 liters (approximately 4.8 to 5.3 quarts) 

This video explains the importance of using the correct transmission fluid for your Chrysler 300 8-speed transmission: 49sZimaleta Motors Mobile Mechanic YouTube · Dec 11, 2023
Important considerations

• Verify your transmission: Chrysler 300s from certain model years, like 2013, could have different 8-speed transmissions (e.g., ZF 8HP45 or 845RE), so it is important to confirm which one you have. 
• No dipstick: Many 8-speed transmissions do not have a traditional dipstick. They are filled from a side port and require a special tool to pump the fluid in. 
• Use the correct fluid: Always use the fluid type recommended in your owner's manual. For 8-speed transmissions, this is often a specific fluid like the Mopar ZF 8 and 9 speed automatic transmission fluid, or an equivalent meeting the ZF Lifeguard 8 specification. 
• Check your owner's manual: The most accurate information for your specific vehicle can be found in your owner's manual.

How many quarts of transmission fluid do I need for a drain and fill?

For a standard transmission fluid drain and fill, you'll typically need 3 to 5 quarts, but you should always measure the amount you drained and refill with the same amount to start, then check the level using the dipstick after running the engine. The exact amount varies by vehicle, and it's crucial to check the owner's manual or look up specifications for your specific make and model, as a drain and fill will not replace all the old fluid. 
How to determine the right amount

• Drain the old fluid: Let the old fluid drain completely. 
• Measure the drained fluid: Measure how much fluid was drained. This is your starting point for refilling. 
• Refill with the measured amount: Put the same amount of new, correct transmission fluid back into the transmission. Using a funnel can help with this process. 
• Start the engine: Start the vehicle and let it run for a few minutes, shifting through all the gears (Park, Reverse, Neutral, Drive) while holding the brake. This circulates the new fluid. 
• Check the level: Turn the engine off and check the fluid level with the dipstick. Add more fluid in small increments if the level is low, or drain a small amount if it's too high. 
• Re-check: Repeat the process of running the engine and checking the dipstick until the fluid level is correct according to the dipstick's hash marks for a "hot" reading. 

Important considerations

• A drain and fill is different from a full transmission flush, which requires significantly more fluid (10-12 quarts or more) because it aims to replace all the fluid, including what's in the torque converter. 
• You should always use the specific type of transmission fluid recommended by your vehicle's manufacturer to avoid damage. 
• Some vehicles, like certain Land Rovers, do not have a dipstick and require a fluid extractor to add new fluid. Consult your owner's manual to be certain. 

What kind of transmission fluid does a Chrysler 300 take?

The correct transmission fluid for a Chrysler 300 depends on the model year, with most automatic transmissions from 2005 and earlier using ATF+4 fluid. However, 8-speed transmissions from 2012 onwards require a specific fluid like Mopar 8 & 9 Speed ATF or a compatible equivalent like ZF Lifeguardfluid8. Always check your owner's manual for the exact specification, as using the wrong fluid can cause damage. 
For most older models (pre-2012)

• Fluid Type: ATF+4 is the standard. 
• Compatible fluids: Look for fluids that explicitly state they meet Chrysler specifications MS-9602 and MS-7176E/D. 
• Examples: Mopar ATF+4 or compatible fluids from brands like Valvoline, Castrol, and FRAM. 

For 2012 and newer 8-speed models

• Fluid Type: A specific fluid designed for ZF 8-speed transmissions is required. 
• Compatible fluids: Look for fluids that are a direct replacement for ZF Lifeguardfluid8. 
• Examples:
  • Mopar 8 & 9 Speed ATF 
  • Ravenol 8HP fluid 
  • Eurol 6700 transmission fluid 

Important considerations

• Check the owner's manual: This is the most reliable way to determine the correct fluid for your specific vehicle's year, make, and model. 
• Use the right type: Using the wrong fluid can lead to poor performance and transmission damage, so be sure to get the correct type for your transmission (4-speed, 5-speed, or 8-speed).