How much fluid does a 2010 4L60E take?
The 2010 4L60E transmission, a popular automatic transmission used in various General Motors vehicles, requires a specific amount of fluid to function properly. According to the information gathered from reliable sources, the 2010 4L60E transmission typically takes around 5.5 to 6 quarts of fluid.
Detailed Explanation
The 4L60E transmission is a four-speed, electronically controlled automatic transmission that was widely used in GM vehicles, including the Chevrolet Silverado, Tahoe, and Suburban, as well as the GMC Sierra and Yukon, from the late 1990s to the early 2010s. The 2010 model year represents a specific version of this transmission, and the fluid capacity can vary slightly depending on the vehicle and other factors.
According to the information gathered from various automotive sources, the typical fluid capacity for a 2010 4L60E transmission is as follows:
- Fluid Capacity: 5.5 to 6 quarts
- Fluid Type: Dexron-VI or equivalent automatic transmission fluid
- Fluid Change Interval: Typically every 30,000 to 60,000 miles, or as recommended by the vehicle manufacturer
It's important to note that the exact fluid capacity may vary slightly depending on the specific vehicle and any modifications or additions made to the transmission system. Always refer to the vehicle's owner's manual or consult a professional mechanic for the most accurate fluid capacity information for your 2010 4L60E transmission.
Proper Fluid Maintenance
Maintaining the proper fluid level and using the recommended fluid type is crucial for the longevity and performance of the 4L60E transmission. Regularly checking and changing the transmission fluid according to the manufacturer's recommendations can help prevent costly repairs and ensure the smooth operation of the transmission.
If you have any further questions or concerns about the fluid requirements for your 2010 4L60E transmission, it's best to consult a qualified automotive technician or refer to the specific information provided by the vehicle manufacturer.
How many quarts does a 5.3 L take?
Capacity: 8 quarts (with filter). After refill check oil level.
How many quarts of transmission fluid do I need for a change?
Drivers can expect to pay $125 to $250 for a transmission fluid flush service. This is approximately twice as much as a transmission fluid change. This is due in large part to the additional fluid required. A flush will take 12 to 22 quarts, while a fluid change requires 5 to 7 quarts.
Is 4 quarts of transmission fluid enough?
You might need 3 to 5 quarts of fluid for a standard automatic transmission car.
How much transmission fluid does a 2010 Chevy Silverado take?
6 quarts
Automatic Transmission Fluid
Capacity: 6 speed 6L90 Total Fill 12.4 quarts. Capacity: 6 quarts Initial Fill.
How much transmission fluid does a 4L60E need?
The 4L60E transmission typically requires approximately 12 quarts of transmission fluid for a new installation, while a fluid change usually requires around 5 quarts of fluid.
How many quarts does a 2010 5.3 take?
6 quarts
Capacity: 6 quarts (with filter). After refill check oil level.
How much transmission fluid does a 2011 Chevy Silverado 1500 5.3 take?
Fill the transmission with 6 quarts of DEXRON VI Transmission Fluid.
What happens if you overfill transmission fluid?
Excessive fluid prohibits proper lubrication and cooling and slows the rotating crankshaft, similar to the effect of running through water. When the air above mixes with the high levels of fluid, it creates a foamy substance that saturates the transmission. This can lead to: Part pitting.
How much transmission fluid does a 5.3 Chevy take?
Automatic Transmission Fluid
Capacity: 6 quarts Initial Fill.
Do I fill the torque converter before installing?
But you you put it in the transmission. First. And it's good practice to fill that up as much as you can. Sometimes you can get quite a bit of fluid in there. So you fill it up let the bubbles.
