How much horsepower does a 1987 Chevy S10 2.8 have?
The 1987 Chevy S10 2.8-liter engine produced 110 horsepower. This compact pickup truck was powered by a 2.8-liter V6 engine that was a popular option for the S10 model during the late 1980s.
Detailed Breakdown of the 1987 Chevy S10 2.8 Engine
The 1987 Chevy S10 was available with several engine options, but the 2.8-liter V6 was one of the most common choices. This engine was part of Chevrolet's 60-degree V6 engine family, which had been in production since the late 1970s.
The 2.8-liter V6 in the 1987 S10 had the following key specifications:
- Displacement: 2.8 liters (173 cubic inches)
- Horsepower: 110 hp @ 4,400 rpm
- Torque: 145 lb-ft @ 2,800 rpm
- Compression ratio: 9.2:1
- Fuel system: Throttle-body fuel injection
This engine was paired with either a 5-speed manual transmission or a 4-speed automatic transmission, depending on the buyer's preference. The 2.8-liter V6 provided a good balance of power and fuel efficiency for the compact S10 pickup.
Comparison to Other Engine Options
In addition to the 2.8-liter V6, the 1987 Chevy S10 was also available with a 2.5-liter inline 4-cylinder engine that produced 100 horsepower. There was also an optional 4.3-liter V6 engine that generated 155 horsepower, which provided more power for towing and hauling.
The 2.8-liter V6 was a popular middle ground, offering more power than the base 4-cylinder while being more fuel-efficient than the larger 4.3-liter V6. This made it a common choice for S10 buyers who wanted a balance of performance and efficiency.
How much horsepower does a 1987 S-10 2.8 have?
A powerful 2.8 Liter V6 with Electronic Fuel Injection is optional on all S-10 Pickups. SAE net horsepower is 125 at 4,800 RPM; net torque is 150 ft. -lbs. at 2,400 RPM.
What is the rarest Chevy S-10?
ss s10 . Baja s10 from the 80s . The EV S10 is the rarest of them all but these ones just aren't around.
What size motor is a 2.8 L?
Engine Size Chart
| Liters (L) | Cubic Centimeters (CC) | Cubic Inches (cid) |
|---|---|---|
| 2.8 | 2,835 | 173 |
| 3.0 | 2,967 | 181 |
| 3.2 | 3,212 | 196 |
| 3.3 | 3,278 | 200 |
What does C10 stand for Chevy?
The “C” in C10 specifies that a particular truck is a two-wheel drive model. On the other hand, trucks that were equipped with four-wheel-drive were identified with the letter “K”. The two-wheel-drive half-ton variation within the C/K lineup was designated as the C10 while the four-wheel-drive version was dubbed K10.
What car is a 2.8 L V6 from?
The 2.8 L (2,837 cc) 60° V6 was used in these vehicles: 1987–1989 Buick Century. 1988–1989 Buick Regal. 1987–1988 Cadillac Cimarron.
Can a V6 outperform a V8?
V-6 engines have improved performance compared to V-8 engines, especially when timing acceleration properly because there's less tendency to drift to the outer edge. However, you can lose a little bit of the power ceiling with the weight advantage.
How much horsepower does a s10 SS have?
A 4.3 L V6 (which was optional on regular S-10s) was the standard engine used in the SS, producing between 180 and 200 hp (149 kW).
How much horsepower does a 2.9 Vortec have?
185 hp
The LLV (also called Vortec 2900) is a 2.9 L; 178.3 cu in (2,921 cc) straight-4 DOHC engine produced between 2007 and 2012, with a 95.5 mm × 102 mm (3.76 in × 4.02 in) bore and a stroke. It replaced the LK5 and produced 185 hp (138 kW) at 5,600 rpm and 190 lb⋅ft (258 N⋅m) of torque at 2,800 rpm.
How much horsepower does a 2.8 L GM have?
2.8L I-4 LWN Features & Specifications
Latest Refinements vs. 2024 and Earlier Models: Horsepower increase from 181 hp to 204 hp.
How much horsepower can you get out of a 2.8 V6?
As for horsepower, Normally aspirated with the Fiero intake you can get to about 190-195hp. Using aftermarket intake and parts you can get to 225hp.
