Loading
  • 2 Ipswich St, Fyshwick ACT 2609
Free Quote
Home FAQ

How much oil does a 2017 200 Series take?

The oil capacity for the 2017 Land Cruiser 200 Series depends on the engine installed. In the petrol 4.6L V8, it takes roughly 7.5–7.7 quarts (about 7.1–7.3 liters) with the filter. The 4.5L diesel V8 requires more oil, typically around 11–12 quarts (approximately 10.5–11.5 liters) with the filter. Always verify the exact figure in the owner’s manual or on the vehicle’s service documentation, as regional variants can exist.


Engine options in the 2017 200 Series


Below are the two primary engine configurations offered in many markets for the 2017 model year and their typical oil capacities.


Petrol 4.6L V8 (1UR-FE)


The gasoline-powered variant uses a smaller oil capacity than the diesel, reflecting its different engine design. The following figure refers to oil capacity including the filter change.



  • Oil capacity (with filter): approximately 7.5–7.7 quarts (7.1–7.3 liters).


Note: Some regional service sheets quote slightly different figures; always verify on the vehicle's oil capacity label or in the official workshop manual.


Summary for petrol: The petrol variant’s oil needs are in the mid-low single-digit gallon range, notably less than the diesel variant due to engine size and configuration.


Diesel 4.5L V8 (1VD-FTV)


The diesel engine has a higher oil capacity due to its turbocharged V8 design and longer service intervals. The following figure refers to oil capacity including the filter change.



  • Oil capacity (with filter): approximately 11.0–11.5 quarts (10.4–11.0 liters).


Concluding about diesel: For the diesel variant, plan for roughly the equivalent of a large can of motor oil plus additional to accommodate the filter change. Always confirm with the owner's manual as some markets list up to 11.7 quarts in certain service specifications.


Additional considerations


When performing an oil change, use the recommended viscosity and grade for your engine as specified by Toyota. Also account for whether you are doing a simple drain-and-fill or a full oil change with filter; this changes the exact quantity needed.


Summary: The 2017 Land Cruiser 200 Series oil capacity varies by engine; roughly 7.5–7.7 qt for the petrol 4.6L V8 and around 11–11.5 qt for the diesel 4.5L V8, including the oil filter. Always verify the exact specification for your vehicle's engine code and market. The owner’s manual or Toyota service information is the authoritative source.


Conclusion


Oil capacity is engine-specific. For the 2017 Land Cruiser 200 Series, petrol models use about 7.5–7.7 quarts (7.1–7.3 liters) with filter, while diesel models require about 11–11.5 quarts (10.4–11.0 liters) with filter. Always check your VIN, engine code, and regional documentation to confirm the exact amount for your vehicle.


Summary


In short, the 2017 Land Cruiser 200 Series’ oil capacity is engine-dependent: petrol around 7.5–7.7 quarts and diesel around 11–11.5 quarts, including the filter. For precise figures, consult the owner’s manual or a Toyota dealership.

How much engine oil does a 200 series LandCruiser take?


The LC200 oil capacity varies by engine: the 1UR-FE engine requires 7.5 liters (service fill) before 2020 or 8.0 liters from 2020 onwards. The 1VD-FTV (diesel) engine requires 9.2 liters. Other engine options like the 1GR-FE require around 6.1 liters, and the 2UZ-FE needs about 7.2 liters. Always check your owner's manual for the exact capacity for your specific vehicle. 
Engine oil capacity by engine model

  • 1UR-FE (Petrol):
    • Before 2020: 7.5 liters (service fill)
    • From 2020: 8.0 liters
  • 1VD-FTV (Diesel): 9.2 liters
  • 1GR-FE (Petrol): Approximately 6.1 liters
  • 2UZ-FE (Petrol): Approximately 7.2 liters (7.5 quarts) 

Important considerations
  • Always check the dipstick: After refilling, it is crucial to check the oil level with the dipstick to ensure it's at the correct level and not over or under-filled. 
  • Consult your owner's manual: For the most accurate information for your specific vehicle, always refer to your owner's manual. 
  • Filter replacement: The capacities listed are for a service fill, which includes replacing the oil filter. 



What kind of oil does a 2017 Chrysler 200 take?


The 2017 Chrysler 200 requires SAE 0W-20 or SAE 5W-20 oil, depending on the engine. You should use 0W-20 for the 2.4L 4-cylinder engine or 5W-20 for the 3.6L V6 engine. It's best to use a full synthetic oil and ensure it meets the Chrysler MS-6395 specification. The engine oil capacity for most models is 5.5 quarts with a filter change. 
Oil type by engine

  • 2.4L 4-cylinder engine: Use SAE 0W-20 full synthetic oil. 
  • 3.6L V6 engine: Use SAE 5W-20 full synthetic oil. 

Important considerations
  • Always check your owner's manual: The most accurate information for your specific vehicle can be found in the owner's manual.
  • Look for the Chrysler MS-6395 specification: Using oil that meets this specification is recommended for engine longevity. 
  • Capacity: The oil capacity is typically 5.5 quarts with a filter change, but always verify with your owner's manual and check the dipstick to confirm the correct level after refilling. 



What kind of oil does a 2017 Lexus 200t take?


The correct oil for a 2017 Lexus IS200t is a full synthetic SAE 0W-20 motor oil. The vehicle's engine requires 4.9 quarts of oil with a filter change. It's recommended to use a full synthetic oil to provide optimal protection for the engine. 

  • Oil type: SAE 0W-20 full synthetic motor oil. 
  • Oil capacity: 4.9 quarts (with filter change). 
  • Why this oil: Using 0W-20 full synthetic oil is essential for the performance and protection of the 2.0L turbo engine. Full synthetic oils are engineered to provide superior protection in modern engines, including those with GDI and turbo technology. 



How much oil does a 2017 BMW take?


The 2017 BMW oil capacity varies by engine, with common models like the 2.0L 4-cylinder requiring around 5 to 5.5 quarts, while a 3.0L 6-cylinder needs about 6.9 quarts and a 4.4L 8-cylinder holds approximately 10.6 quarts. It is crucial to check your specific engine's requirements before adding oil, and always verify the final level with the electronic dipstick after refilling. 
This video demonstrates the process of changing the oil and filter on a 2017 BMW 530i: 1mPortuguese DIY DadYouTube · Jan 16, 2025
Examples by engine:

  • 2.0L 4-cylinder (e.g., 320i, 330i, 530i): Approximately 5.1 to 5.5 quarts, depending on the specific engine code. 
  • 3.0L 6-cylinder (e.g., 640i): Around 6.9 quarts. 
  • 4.4L 8-cylinder (e.g., 750i): Up to 10.6 quarts. 

You can watch this video to see how to change the oil on a 2017 BMW X1: 53sShawn BargeYouTube · Aug 21, 2022
Important considerations:
  • Verify your engine: The capacity changes significantly between engine types, so always confirm the capacity for your specific vehicle. 
  • Check the level electronically: After refilling, use the car's electronic oil level indicator to ensure you have the correct amount, as the onboard computer can be more accurate than a physical dipstick. 
  • Use the correct oil: Ensure you are using the correct viscosity grade (like 0W-20 or 0W-30) and BMW-approved LL-01 or LL-04 oil. 
  • Replace the drain plug seal: It's recommended to replace the drain plug seal with each oil change to prevent leaks. 

This video shows an oil change for a 2017 BMW 330i with an N20 engine: 48sSaints MotorsportsYouTube · Nov 17, 2022


Kevin's Auto

Kevin Bennett

Company Owner

Kevin Bennet is the founder and owner of Kevin's Autos, a leading automotive service provider in Australia. With a deep commitment to customer satisfaction and years of industry expertise, Kevin uses his blog to answer the most common questions posed by his customers. From maintenance tips to troubleshooting advice, Kevin's articles are designed to empower drivers with the knowledge they need to keep their vehicles running smoothly and safely.