How much oil does a 2024 Ford Bronco 2.3 take?
On a typical oil-change for the 2024 Bronco equipped with the 2.3-liter EcoBoost engine, you’ll need about five quarts of engine oil (roughly 4.7 liters), including a new filter. Always confirm the exact figure in the owner's manual or with a dealer for your specific configuration.
Oil capacity and maintenance for the 2.3L EcoBoost Bronco
The 2.3L EcoBoost is Ford’s compact, turbocharged four-cylinder that powers most Bronco trims. The official capacity is commonly listed as five quarts with a new filter, though the exact amount can vary slightly depending on drain procedure and whether the filter is replaced.
Before getting into the details, here is a concise guide to the oil capacity and related maintenance for this engine:
- Oil capacity: 5 quarts (4.7 liters) with the filter installed.
- Recommended oil viscosity: synthetic 5W-30 that meets Ford specifications (check your manual for exact specs).
- Oil filter: change the filter at every oil change to ensure proper filtration and capacity accounting.
- Top-off and overfill: add oil gradually, then recheck the dipstick to avoid overfilling, which can cause high oil pressure and leaks.
- Maintenance interval: follow Ford’s recommended service interval in the owner's manual or through a dealer, typically around every 5,000–7,500 miles under normal driving; adjust for severe conditions.
Bottom line: plan to have about five quarts on hand for a standard change, replace the filter, and verify the oil level with the dipstick after filling to the recommended mark.
Oil type and service specifics
Use synthetic 5W-30 engine oil that meets Ford specifications. Confirm the exact specification (such as Ford WSS-M2C93 or equivalent) in the owner's manual or with a Ford dealer. Adhering to the recommended oil type helps maintain engine protection, efficiency, and warranty coverage.
Additionally, consult the vehicle’s manual for the maximum oil capacity if performing non-standard changes, such as when only draining oil without changing the filter or when replacing the oil pan drain plug, and always use the dipstick to verify actual oil level after topping up.
Summary
The 2024 Ford Bronco with the 2.3-liter EcoBoost typically requires about five quarts (roughly 4.7 liters) of engine oil for a standard change, including a new filter. Use synthetic 5W-30 and verify the exact capacity and specification in the owner's manual. Regular maintenance and correct oil level checks help protect the engine and maintain performance.
How much oil does a 2.3 L 4 cylinder take?
6 quarts
6 quarts (with filter).
How much oil goes in a 2024 Ford Bronco 2.3 L?
Capacities and Specifications - 2.3L EcoBoost
| Item | Capacity |
|---|---|
| Engine oil (with oil filter) | 5.7 qt (5.4 L) |
| Engine coolant | 11.6 qt (11 L) |
| Brake fluid | Between MIN/MAX on brake fluid reservoir |
| Rear axle fluid | 2.4 pt (1.15 L) |
What kind of oil does a 2.3 L Bronco take?
The recommended oil for a Ford Bronco 2.3L is SAE 5W-30 synthetic blend or full synthetic, meeting the Ford specification WSS-M2C961-A1. In extreme climates below -29∘negative 29 raised to the composed with power−29∘C (–20∘– 20 raised to the composed with power–20∘F), you can use 0W-30 synthetic oil meeting specification WSS-M2C963-A1. The engine capacity is approximately 6 quarts with a filter change.
Recommended oil
- Primary: SAE 5W-30 (synthetic blend or full synthetic)
- Ford Specification: WSS-M2C961-A1
- Extreme Cold (< -29°C): SAE 0W-30
- Ford Specification (Extreme Cold): WSS-M2C963-A1
Capacity
- With filter change: Approximately 6 quarts
What is the 2024 Ford Bronco 2.3 L 4 cylinder engine?
2024 Ford Bronco Engine Specs & Towing Capacity
Go with the standard 2.3L inline four-cylinder (I4) engine for up to 300 horsepower; it's the only Bronco engine offered with either a manual or automatic transmission.
