How much oil does a 4.7 L Dodge engine take?
Typically about 6 quarts (5.7 liters) of oil when you replace the oil filter; around 5 quarts (4.7 liters) if you’re performing a drain-and-fill without changing the filter. Exact capacity can vary by model year and configuration, so it’s best to confirm with the owner’s manual for your vehicle.
The 4.7 L Dodge engine refers to the PowerTech V8 used in several Dodge and Jeep models, including the Durango, Grand Cherokee, Ram, and Dakota. While the general oil capacity is widely cited, small differences between model years and filter sizes mean you should verify for your specific application.
Oil capacity by scenario
Below are typical figures you may encounter in maintenance guides. Use them as a baseline, but always check your vehicle’s documentation.
- With oil filter replacement: approximately 6 quarts (about 5.7 liters).
- Without replacing the filter (drain and fill): approximately 5 quarts (about 4.7 liters).
- Engine fully drained of all oil (dry engine): roughly 7 quarts (about 6.6 liters) to reach the full level after a complete fill and initial start-up procedure.
These values are typical for many 4.7 L PowerTech V8 installations, but variations can occur by model, year, and filter size. Always verify with the vehicle’s manual or a trusted service guide and use the dipstick to confirm the correct oil level.
Practical steps to measure and fill
When performing an oil change, follow these steps to ensure you use the correct amount and achieve a proper oil level.
- Warm up the engine briefly, then turn it off and park on level ground.
- Drain the old oil completely from the pan, replace the drain plug, and remove/replace the oil filter as needed.
- Pour in the recommended starting quantity (a typical fill starts around 5–6 quarts, depending on whether you’ve replaced the filter).
- Start the engine and run for a minute, then check for leaks and turn off the engine.
- With the engine off, wait a few minutes for the oil to settle, then check the dipstick and add oil in small amounts until the level is between the marks.
- Recheck after the engine has run and cooled, and reseal the oil fill cap.
By following these steps, you’ll ensure the engine has the proper oil level, reducing the risk of overfill or underfill. Dispose of used oil responsibly at a recycling facility.
Summary
In short, the 4.7 L PowerTech V8 commonly takes about 6 quarts (5.7 liters) of oil with a new filter, and around 5 quarts (4.7 liters) for a drain-and-fill without a filter change. Exact capacity can vary by model year and configuration, so always consult the owner’s manual and verify with the dipstick during your oil change. Properly filled oil helps protect the engine and maintain performance.
What kind of oil does a 2003 Dodge Ram 4.7 take?
5w30
Genuine Mopar Engine Oil Change Kit 2003 Dodge RAM 1500 4.7L V8 engine oil 5w30.
How much oil does a 2002 Dodge Ram 1500 4.7 L take?
6 qt.
ENGINE: NEXT-GENERATION 4.7-LITER MAGNUM, SOHC, 12-VALVE SMPI V-8
| Availability | Std.—All Quad Cabs™ and 4WD regular cabs |
|---|---|
| Fuel Requirement | Unleaded regular, 87 octane (R+M)/2 |
| Oil Capacity | 6 qt. (5.7L) |
| Emission Controls | Three-way catalytic converter and internal engine features(a) |
What kind of oil does a 4.7 Dodge Ram take?
The recommended oil for a Dodge 4.7L engine is typically 5W-30, especially for engines 2006 and older, while some sources suggest 5W-20 for newer models. Always check your owner's manual or the oil cap for the specific recommendation for your year and model, and ensure the oil meets the required API service standards.
Oil type and weight
- 5W-30: This is the most common and recommended oil for many 4.7L engines, particularly older models like the 2003 and 2006 Rams. It is available in both conventional and full synthetic forms.
- 5W-20: Some newer models, such as the 2012 Ram 1500, specify 5W-20. It is crucial to verify the exact recommendation for your engine's model year, as seen on the oil cap or owner's manual.
How to choose
- Check your owner's manual: This is the most reliable source for the correct oil type and viscosity for your specific vehicle.
- Look at the oil cap: The correct oil weight is often printed on the engine's oil filler cap.
- Consider the environment: While the manufacturer specifies the viscosity, synthetic oils are often a good choice for better protection and performance across a wider temperature range.
How many quarts of oil go in a 4.7 Dodge engine?
A 4.7L Dodge engine typically holds 6 quarts of oil when the filter is changed. However, it's always best to double-check the owner's manual for the specific year and model, as some years or specific applications may have slight variations.
- Capacity: 6 quarts (with filter) for most models.
- Recommendation: Check your owner's manual to confirm the exact amount for your vehicle.
- Post-change: After refilling, check the oil level with the dipstick to ensure it is correct.
