How much oil goes in a 2014 Acura MDX?
The 2014 Acura MDX with the 3.5-liter V6 engine requires 5.5 quarts of engine oil when performing a full change, including the filter, and the recommended oil is 0W-20 synthetic. This provides the proper lubrication and performance for daily driving and longer service intervals.
Oil capacity and oil specifications
Understanding the capacity and the right oil type helps ensure your MDX runs smoothly between service visits. The following details apply to the standard 2014 MDX configuration with the 3.5L V6 engine.
Engine details
Engine: 3.5-liter V6 with i-VTEC. This model typically uses 0W-20 synthetic oil and requires a full-change capacity of 5.5 quarts when replacing the filter.
- Capacity: 5.5 quarts (5.2 liters) with filter
- Recommended oil grade: 0W-20 synthetic (ACDelco-style phrasing not applicable; use Honda/Acura-approved 0W-20)
- Viscosity specification: 0W-20, meeting current GF-5 or newer standards as specified by Acura/Honda
- Filter: Use a genuine Acura/Honda oil filter or an equivalent recommended by Acura
Before you start a change, know these core figures and requirements:
Note: Always verify the exact specification in your owner's manual or with a dealer, as regional climate and warranty considerations can influence the exact grade and capacity guidance.
In practice, the 5.5-quart figure is the standard baseline for a full oil change with the filter installed. If you drain and refill without replacing the filter, the capacity used will be slightly different, but for routine maintenance, plan on 5.5 quarts.
How to perform an oil change on the 2014 MDX
When performing an oil change yourself or overseeing a shop service, follow these steps to ensure a correct fill and proper lubrication of the engine.
- Warm the engine to operating temperature to help drain the old oil completely.
- Park on a level surface, engage the parking brake, and raise the vehicle if needed for access to the drain plug.
- Place a drain pan underneath, remove the drain plug, and allow the old oil to drain completely.
- Remove and replace the oil filter with a new Acura/Honda filter or approved equivalent.
- Reinstall the drain plug securely and pour in 5.5 quarts of 0W-20 synthetic oil.
- Check the oil level with the dipstick and add more oil as needed to bring it to the full mark.
- Start the engine, look for leaks, and recheck the oil level after a few minutes of running and settling.
Following these steps helps ensure the engine is properly lubricated and avoids overfilling or underfilling, which can affect performance and longevity.
Summary
The 2014 Acura MDX uses 5.5 quarts (about 5.2 liters) of engine oil when performing a full change with the filter, with 0W-20 synthetic oil recommended for most climates. Use a genuine or approved filter and verify the exact specifications in your owner's manual. Regular checks with the dipstick and adherence to the manufacturer guidelines will help maintain performance and reliability.
How many quarts of oil does a 3.6 L V6 take?
A 3.6L V6 engine typically takes between 5 and 6 quarts of oil, but the exact amount varies by vehicle model, so you must check your owner's manual or the oil fill cap for the precise capacity. For example, some models like a 2013 Jeep JK require 6 quarts, while newer models like a 2020 Jeep Wrangler or 2018+ Jeep Wrangler JL may only take 5 quarts.
Here are some general guidelines:
- Check your owner's manual: This is the most reliable source for your specific vehicle.
- Look at the oil fill cap: It may have the required viscosity and capacity printed on it.
- Consider the model year: Newer vehicles, especially certain Jeep models, have different oil capacities than older ones.
- Change the oil filter: Always include an oil filter change, as this is part of the full oil capacity.
- After refilling, check the level: After you've filled the engine with oil, use the dipstick to check the oil level and add more if needed to reach the "full" line.
How many quarts of oil does a 2014 Acura MDX take?
A 2014 Acura MDX takes 5.7 quarts of oil when replacing the filter. The recommended oil is a 0W-20 viscosity grade, and it's important to check the dipstick after refilling to ensure the correct level.
- Oil Capacity: 5.7 quarts (with filter change)
- Recommended Oil: 0W-20
- Important: Always check the dipstick after the oil change to confirm the correct fill level.
How much oil does a 3.5 liter V6 engine take?
6.0 qt
Capacities and Specifications - 3.5L Ecoboost
| Item | Capacity |
|---|---|
| Engine oil (with oil filter) | 5.7 L (6.0 qt) |
| Engine coolant | 12.4 L (13.1 qt) |
| Brake fluid | Between MIN/MAX on brake fluid reservoir |
| Rear axle fluid (four-wheel drive) | 2.11 pt (1.0 L) |
How many quarts of oil does a Acura MDX take?
The Acura MDX oil capacity varies by model year and engine type, but most 3.5L V6 engines require around 5.7 quarts of oil with a filter, while the Type S models with a 3.0L turbocharged V6 hold about 6.0 quarts. Newer models often have slightly different capacities, such as the 2025 MDX using 5.5 quarts, so it is always best to check the owner's manual or the dipstick after an oil change.
Typical capacities by engine type
- 3.5L V6: Around 5.7 quarts (with filter)
- 3.0L Turbocharged V6 (Type S): Approximately 6.0 quarts (with filter)
- Model-specific variations: Some newer models might have slightly different capacities, like the 2025 MDX at 5.5 quarts. Older models will have different requirements, such as the 2013 model needing 4.5 quarts.
Important considerations
- Always check your owner's manual: This is the most reliable source for your specific vehicle's oil capacity.
- Check the dipstick: After filling the oil, run the engine briefly, then check the dipstick to ensure the level is correct and add more if needed.
- Replace the filter: It is essential to replace the oil filter at every oil change.
- Use the correct oil type: Always use the manufacturer-recommended oil type, such as 0W-20 for newer models, to ensure engine longevity.
