How much transmission fluid does a 2013 Dodge Dart 1.4 manual take?
About 1.9–2.0 quarts (roughly 1.8–1.9 liters) of manual transmission fluid is typically needed for a complete drain-and-fill on the 2013 Dodge Dart with the 1.4-liter engine. Exact capacity can vary slightly by transmission variant and service history, so check your owner’s manual or confirm with a Chrysler dealer for your specific car.
Estimated capacity and recommended fluid
Below are commonly cited figures and guidance for the 2013 Dart 1.4’s manual transmission. These values reflect typical practice for a full drain and refill, but may vary by production date or transmission model.
- Typical drain-and-fill capacity: approximately 1.9–2.0 quarts (about 1.8–1.9 liters).
- Recommended fluid type: a GL-4 (or GL-4/GL-5) gear oil in the 75W-90 or 80W-90 range; use fluids that meet Chrysler/Mopar specifications or the manufacturer’s equivalent for the manual transmission. Some modern GL-5 oils can be used if they meet the transmission’s tolerances, but always verify compatibility.
- Fill method note: remove the fill plug before draining if possible, and fill until the fluid just begins to seep from the fill hole when the transmission is warm and on level ground; reinstall the fill plug and torque to the manufacturer’s specification.
Concluding guidance for this topic: use the exact specification listed in your owner’s manual or by a dealer to ensure you’re using the correct oil and capacity for your particular transmission variant.
Transmission variants in the 2013 Dart
The 2013 Dodge Dart with the 1.4-liter engine typically uses a six-speed manual transmission. While the capacity figures above cover common configurations, variations in transmission design or production could alter exact capacity. Always verify the correct spec for your specific VIN if you’ve learned that your car differs from the standard setup.
How to change and verify the fluid
Before attempting a change, familiarize yourself with the procedure and gather the right tools and fluid. The steps outlined below reflect a typical DIY approach for a complete drain and fill on a manual transmission in this vehicle.
- Park on level ground and ensure the engine is warm to expand the oil slightly for an accurate fill.
- Locate the transmission drain and fill plugs; begin with the fill plug to verify access, then drain from the lower plug if appropriate.
- Carefully remove the fill plug. If oil drips out, the level is good; if not, proceed to drain and then fill.
- With the transmission warm, add fluid slowly through the fill hole using a proper funnel until the oil begins to seep out of the fill hole, then reinstall and torque the fill plug to spec.
- Check for leaks after replacing the fill plug and take the car for a short test drive to ensure smooth shifting; recheck level if needed after cooling down.
Concluding tip: always dispose of used gear oil responsibly and keep a clean workspace to avoid contamination of the fluid.
Tools, tips, and safety tips
Useful items include a hydraulic floor jack and stands (if needed for access), a drain pan, a closed-end wrench for the fill plug, a funnel, and the correct grade of transmission fluid. Wear eye protection and gloves, and follow all safety precautions when working under a vehicle. If you are unsure about fluid compatibility with your specific transmission model, consult a qualified mechanic or your local dealer.
Verification and sources
Capacity figures can vary by production batch and transmission variant. For the most accurate specification, consult your owner’s manual, the service manual for your Dart, or contact a Chrysler dealership. Use fluids that meet the manufacturer’s specifications for your manual transmission to ensure proper shifting performance and longevity.
Summary
For a 2013 Dodge Dart with the 1.4-liter engine and a manual transmission, plan on about 1.9–2.0 quarts of fluid for a full drain-and-fill. Use a GL-4 (or equivalent) gear oil in the 75W-90 or 80W-90 range, fill until the fluid seeps from the fill hole when warm, and recheck after a test drive. Always confirm the exact specification for your vehicle with the owner’s manual or a dealer, as small variations between transmissions can affect the exact capacity.
