Loading
  • 2 Ipswich St, Fyshwick ACT 2609
Free Quote
Home FAQ

How much transmission fluid does a 2013 Ford Transit Connect take?

Around 9 to 10 quarts of automatic transmission fluid for a full fill, with about 4 to 5 quarts typically replaced in a standard drain-and-fill. Use the owner's manual to confirm exact figures for your specific gearbox.


The Transit Connect from 2013 commonly paired a 2.5-liter engine with Ford's automatic transmission; capacity varies by transmission variant and whether you’re flushing the system or simply performing a drain-and-fill. The numbers below reflect typical values for the common configuration.


Capacity figures you should know


Below are the common capacity figures you may encounter when servicing a 2013 Transit Connect with the typical automatic transmission configuration:



  • Total system capacity (full fill): 9.0–9.5 quarts (8.5–9.0 liters).

  • Drain-and-fill replacement amount: roughly 4–5 quarts (3.8–4.8 liters).

  • Full flush replacement (using a flushing machine): about 10.5–11 quarts (9.9–10.4 liters).


These figures can vary by the exact transmission variant and whether the fluid is changed via a simple drain or a full hydraulic flush. Always confirm the precise capacity for your VIN in the owner's manual or Ford service data.


Notes and caveats


Some 2013 Transit Connects use a 4-speed automatic and others may have slight differences in capacity. The fluid type (Mercon V or Mercon LV) and level-reading procedure can also affect the amount you add. Always refer to the exact specifications for your vehicle.


How to check and maintain the transmission fluid


Proper checking and maintenance helps ensure reliability and smooth shifting. Here's a quick guide to the process:



  • Ensure the engine and transmission are at operating temperature before checking.

  • Park on level ground and apply the parking brake.

  • Use the correct Ford-recommended ATF and check the level with the transmission dipstick or the method specified for your model.

  • If topping up, add small increments and recheck the level to avoid overfilling.


If you’re unsure about the specific fluid type or capacity for your vehicle, consult your owner’s manual or a Ford dealership service advisor.


Bottom line: Plan for roughly 9–10 quarts for a full fill, with 4–5 quarts typically replaced in a drain-and-fill on the common 2013 Transit Connect configuration. A full flush will involve more fluid. Always verify with official documentation for your exact transmission variant.


Summary: The 2013 Ford Transit Connect generally takes about 9–11 quarts of ATF depending on whether you perform a drain-and-fill or a full flush, and exact figures vary by transmission variant. Check the owner’s manual at your VIN for the precise specification and follow Ford’s recommended procedure when servicing the transmission.

What kind of transmission fluid does a Ford Transit Connect take?


The correct transmission fluid for a Ford Transit Connect is Mercon LV automatic transmission fluid, but you should always verify with your specific vehicle's owner's manual, as some models may recommend a different type. Motorcraft Mercon LV is the Ford-recommended brand, but other brands that meet the Mercon LV specification are also suitable. 

  • Ford Recommended Fluid: Motorcraft Mercon LV Automatic Transmission Fluid 
  • Alternative Fluids: Other brands that meet the Mercon LV specification can be used. Check the product label to ensure it is compatible with Ford Mercon LV. 
  • How to confirm: Always check your owner's manual or the transmission dipstick to confirm the exact fluid type recommended for your specific model year and transmission. Some newer models may require Valvoline ULV or other fluids. 



How many quarts of transmission fluid for a drain and fill?


For a standard transmission fluid drain and fill, you'll typically need 3 to 5 quarts, but you should always measure the amount you drained and refill with the same amount to start, then check the level using the dipstick after running the engine. The exact amount varies by vehicle, and it's crucial to check the owner's manual or look up specifications for your specific make and model, as a drain and fill will not replace all the old fluid. 
How to determine the right amount

  • Drain the old fluid: Let the old fluid drain completely. 
  • Measure the drained fluid: Measure how much fluid was drained. This is your starting point for refilling. 
  • Refill with the measured amount: Put the same amount of new, correct transmission fluid back into the transmission. Using a funnel can help with this process. 
  • Start the engine: Start the vehicle and let it run for a few minutes, shifting through all the gears (Park, Reverse, Neutral, Drive) while holding the brake. This circulates the new fluid. 
  • Check the level: Turn the engine off and check the fluid level with the dipstick. Add more fluid in small increments if the level is low, or drain a small amount if it's too high. 
  • Re-check: Repeat the process of running the engine and checking the dipstick until the fluid level is correct according to the dipstick's hash marks for a "hot" reading. 

Important considerations
  • A drain and fill is different from a full transmission flush, which requires significantly more fluid (10-12 quarts or more) because it aims to replace all the fluid, including what's in the torque converter. 
  • You should always use the specific type of transmission fluid recommended by your vehicle's manufacturer to avoid damage. 
  • Some vehicles, like certain Land Rovers, do not have a dipstick and require a fluid extractor to add new fluid. Consult your owner's manual to be certain. 



How much transmission fluid does a Ford Transit take?


The transmission fluid capacity for a Ford Transit varies by model, but common total fill capacities are around 13.1 quarts for the 6-speed 6R80 automatic transmission and 13 quarts for models with the 10R80 transmission. For a complete list of capacities and fluid specifications for your specific vehicle, consult the owner's manual or a reliable parts lookup tool. 
Common transmission fluid capacities

  • 6R80 transmission (6-speed): 13.1 quarts (total fill) 
  • 10R80 transmission (10-speed): 13 quarts (total fill) 
  • Initial fill: Typically around 5.1 quarts for the 10R80 and 3.5 quarts for some 6R80 models 

Important notes
  • Always verify: Because capacities can vary by year, engine, and transmission type, always check your specific model's owner's manual or use a parts database for the correct capacity. 
  • Fluid specification: Ensure you use the correct fluid type as specified by Ford. For example, the 10R80 transmission requires a WSS-M2C949-A fluid, which is also sold under the MERCON ULV and DEXRON ULV names. 
  • Initial vs. total fill: The "total fill" capacity is for a complete flush that includes the torque converter. The "initial fill" is the amount of fluid needed for a simple drain and refill, which is less than the total fill capacity. 



How much transmission fluid does a 2013 Ford Transit Connect hold?


The 2013 Ford Transit Connect transmission fluid capacity depends on the engine size and transmission type. For the 2.0L with the 4-speed 4F27E automatic transmission, the total fill is about 7.1 quarts (7.17.17.1 quarts). The 2.5L engine with an automatic transmission capacity is approximately 9.0 quarts (9.09.09.0 quarts). 

Engine Transmission Capacity
2.0L 4-speed 4F27E Automatic 7.1 quarts (total fill)
2.5L Automatic 9.0 quarts
(function(){
(this||self).Wufxzb=function(c,e,f,l,k){var d=document.getElementById(c);if(d&&(d.offsetWidth!==0||d.offsetHeight!==0)){c=d.querySelector("div");var g=c.scrollWidth-c.offsetWidth,h=Math.min(e?g:0,g);c.scrollLeft=e&&(l||f)?0:h;var a=d.getElementsByTagName("g-left-button")[0],b=d.getElementsByTagName("g-right-button")[0];a&&b&&(e=RegExp("\\btHT0l\\b"),f=RegExp("\\bpQXcHc\\b"),a.className=a.className.replace(e,""),b.className=b.className.replace(e,""),h===0?a.className="pQXcHc "+a.className:(a.className=
a.className.replace(f,""),k&&c.classList.add("pA30Ne")),h===g?b.className="pQXcHc "+b.className:(b.className=b.className.replace(f,""),k&&c.classList.add("FpCCub")),setTimeout(function(){a.className+=" tHT0l";b.className+=" tHT0l"},50))}};}).call(this);(function(){var id='_t-UlababN8TWi-gP-O29sAE_111';var rtl=false;var gecko=false;var edge=false;var soh=false;
(this||self).Wufxzb(id,rtl,gecko,edge,soh);})();


Kevin's Auto

Kevin Bennett

Company Owner

Kevin Bennet is the founder and owner of Kevin's Autos, a leading automotive service provider in Australia. With a deep commitment to customer satisfaction and years of industry expertise, Kevin uses his blog to answer the most common questions posed by his customers. From maintenance tips to troubleshooting advice, Kevin's articles are designed to empower drivers with the knowledge they need to keep their vehicles running smoothly and safely.