How much transmission fluid does a 2014 Toyota Tacoma take?
The 2014 Toyota Tacoma can take different amounts of transmission fluid depending on the transmission type. In general, the automatic transmission holds about 12 quarts (roughly 11–12 liters) of ATF, while the manual transmission holds about 2.5–3 quarts (about 2.4–2.8 liters). Exact figures depend on whether you’re performing a full drain and fill, changing the filter, or flushing the system, and whether your model is 2WD or 4WD.
Transmission options for the 2014 Tacoma
Below are the typical capacities associated with the two main transmission types offered for the 2014 Tacoma. The figures reflect common service scenarios (drain and fill, with or without filter change). Always confirm with your owner's manual or a Toyota service bulletin for your specific build.
- Automatic transmission (A750F): Total capacity about 12–13 quarts (11.4–12.3 L). A standard drain-and-fill typically replaces about 9–11 quarts (8.5–10.4 L). A full system flush or a complete drain with filter replacement can approach the full 12–13 quarts.
- Manual transmission (5-speed manual, as used in older configurations of the 2014 Tacoma): Approximate capacity around 2.5–3.0 quarts (2.4–2.8 L).
Because production batches and trim levels can vary, these ranges are intended as guides. The exact capacity for your truck may differ slightly based on drivetrain, whether a filter/gasket is replaced, and the service procedure used.
Fluid type and service guidance
Use the fluid recommended by Toyota for the automatic transmission: Toyota ATF WS (World Standard). Some inspectors and older references may list Dexron VI compatibility, but Toyota-warranted service typically specifies ATF WS. For manual transmissions, use the factory-recommended manual transmission oil specified in the owner’s manual. If you’re performing a fluid change yourself, make sure the engine is warm, the vehicle is secure, and you follow proper drain-and-fill procedures to avoid overfilling or underfilling.
How to approach a DIY drain-and-fill
Before you begin, understand that the steps and quantities differ between automatic and manual transmissions. The following list outlines general guidelines you might encounter during a typical service. If you’re uncertain, consult the service manual for your exact build and safety considerations.
- Automatic transmission:
- Benefit from warming the transmission to operating temperature to ensure accurate fluid level reading.
- Drain the pan, replace the filter (if applicable), reinstall the pan with new gasket, and refill with the recommended ATF WS.
- Expect to replace roughly 9–11 quarts during a standard drain-and-fill; a complete flush will use around 12+ quarts.
- Manual transmission:
- Drain the old fluid from the transmission oil fill/level plug and refill with the correct manual transmission oil.
- Refill to the level specified in the service manual, typically with the vehicle on level ground.
After any drain-and-fill, recheck the level with the appropriate method (dipstick or fill plug) as specified for the transmission type, and take note of any changes in shifting performance.
What to watch for after a refill
After adding new transmission fluid, monitor for appropriate shifting performance, any unusual noises, or fluid leaks. If the fluid level is too high, it can cause foaming and erratic shifting; too low can cause slipping or hard shifts. If you’re unsure about the correct level or the right fluid type, contact a Toyota-certified technician or reference the official service manual for your exact vehicle configuration.
Summary
For the 2014 Toyota Tacoma, automatic transmissions typically require about 12 quarts of ATF (roughly 11–12 liters) for a full drain-and-fill with a filter change, while a drain-and-fill alone usually replaces around 9–11 quarts. Manual transmissions generally hold about 2.5–3.0 quarts. Fluid type matters: use Toyota ATF WS for automatics and the factory-recommended oil for manuals. Always verify exact specifications for your particular model and drivetrain in the owner's manual or a Toyota service bulletin, and consider consulting a professional if you’re unsure about the procedure.
