What is the torque for a 2012 Ford Fusion?
The 2012 Ford Fusion has a torque output that varies depending on the engine configuration. The base 2.5L 4-cylinder engine produces 175 lb-ft of torque, while the available 3.5L V6 engine generates 263 lb-ft of torque.
Engine Torque Specifications
The 2012 Ford Fusion was offered with two engine options:
- 2.5L 4-cylinder engine: 175 lb-ft of torque
- 3.5L V6 engine: 263 lb-ft of torque
Torque is a measure of the rotational force an engine can produce, which is important for acceleration and towing capacity. The higher the torque output, the more power the engine can deliver to the wheels.
Transmission and Drivetrain
The 2.5L 4-cylinder engine was paired with a 6-speed automatic transmission, while the 3.5L V6 engine could be equipped with either a 6-speed automatic or a 6-speed manual transmission. Both engines were available in front-wheel-drive or all-wheel-drive configurations.
The combination of engine torque, transmission, and drivetrain setup can significantly impact the overall performance and driving characteristics of the 2012 Ford Fusion.
What is the torque spec for Ford Fusion spark plugs?
Yes, 10 ft/lbs is "sufficient". It's in between 7 and 15.
What are the torque settings for cylinder head bolts?
1> Small Engines (e.g., motorcycles, small cars): Typically, the torque for cylinder head bolts might range from about 60 to 100 foot-pounds (ft-lbs) or 80 to 135 Newton-meters (Nm).
How much torque does a 2012 Ford Fusion have?
"With 175 horsepower and 172 lb-ft of torque, the four-cylinder Fusion is hardly a sports sedan, but that doesn't mean it's not a fun drive."
What is the correct torque for wheel nuts?
around 100 pound-feet
Most vehicles have lug nuts that require around 100 pound-feet of torque, but some vehicles require more or less. It's best to check your vehicle's manual to find out the exact specifications you need. You should properly torque your lug nuts when installing new wheels and after driving 50 to 100 miles on new wheels.
What is the proper torque for spark plugs?
Recommended Torque and Tightening Angle
| Thread Size | Applicable Models | Recommended Torque |
|---|---|---|
| M10 | Stainless Gasket Type ( *1 ) | 10-15N・m |
| M12 | All Types | 15-20N・m |
| M14 | Types other than the ones shown below | 20-30N・m |
What is the lug nut torque on a 2012 Ford Fusion?
Tighten the wheel nuts in a star pattern to 98 ft. lbs.
What is the torque spec for an oil drain plug?
Torque Specs for the Oil Drain Plug
but will usually fall between 18 and 25 lbs ft. Experts claim that applying this amount of force using an oil drain plug torque wrench is enough to bring the plug's rubber gasket close to the oil pan and seal the hole.
What is the torque spec for lug nuts?
Most vehicles have lug nuts that require around 100 pound-feet of torque, but some vehicles require more or less. It's best to check your vehicle's manual to find out the exact specifications you need. You should properly torque your lug nuts when installing new wheels and after driving 50 to 100 miles on new wheels.
What is the torque spec on lug nuts Ford?
Ford Lug Nut Torque Specs
The torque spec for most Ford vehicles with 14mm wheel studs is 150 ft-lbs.
What torque should bolts be?
US Recommended Bolt Torque
| Size | Recommended Torque | |
|---|---|---|
| Grade 2 | Grade 8 | |
| 1/2" | 37 | 80 |
| 9/16" | 53 | 115 |
| 5/8" | 73 | 159 |
