What is the torque on Honda Fit lug nuts?

In most Honda Fit models, lug nuts are tightened to about 80 ft-lbs (108 N·m). This value can vary slightly by year, trim, and wheel type, so always verify with your owner's manual or dealer for your exact vehicle.

Official torque specification

The torque specification commonly cited for factory lug nuts on Honda Fit wheels is 80 ft-lbs (108 N·m). Some sources note 79 ft-lbs (107 N·m) for certain year/wheel configurations. Always check your specific manual to confirm the correct value for your car’s exact setup.

• Torque value: 80 ft-lbs (108 N·m) is the standard target for most Fit models with factory wheels.


• Alternative value: 79 ft-lbs (107 N·m) may appear in some manuals or service guides for particular years or wheel packages; verify for your vehicle.


• Re-torque recommendation: After installing wheels, recheck torque after driving 50–100 miles (80–160 km) to account for seating and any settling.

Always use a calibrated torque wrench and apply the specified torque value; avoid relying on rough fingertip feel or “snug and go.”

Proper lug-nut tightening procedure

To ensure even seating and safe operation, follow a consistent tightening process using a cross-pattern sequence.

1. Before lifting the car (or after placing the wheel), loosen the lug nuts slightly if the wheel is already mounted; otherwise tighten them finger-tight in a stepwise manner once the wheel is in place.


2. Tighten the lug nuts in a star/crisscross pattern to seat the wheel evenly.


3. Torque in small increments until you reach the final specification (80 ft-lbs / 108 N·m) for each nut, maintaining the cross pattern.


4. Use the correct socket size for the Fit’s lug nuts and a torque wrench for the final pass; avoid using impact tools for the final torque.

After completing the tightening, recheck all lug nuts once the vehicle has been driven a short distance to confirm they remain at the correct torque.

Model-year and wheel-size differences

While 80 ft-lbs (108 N·m) is the common figure for many Honda Fit generations, some model years or wheel configurations list a slightly different value (e.g., 79 ft-lbs / 107 N·m). Always verify against your specific year, trim level, and wheel size, and consult the service manual or dealer if you’re unsure. Aftermarket wheels or spacers can also affect the required torque, so follow the manufacturer’s guidance for those setups.

Summary

For most Honda Fit models, tighten lug nuts to 80 ft-lbs (108 N·m) and recheck after a short drive. If your manual lists a different figure (such as 79 ft-lbs / 107 N·m), follow that specification. Use a proper torque wrench, perform a cross-pattern tightening, and re-torque to ensure wheel safety and reliability.

Is 50 mile retorque necessary?

This is typically recommended after the first 50-100 miles of driving to account for any settling that may occur. Regular Maintenance: Regular retorquing should be part of your routine maintenance schedule. Consider having your lug nuts retorqued every 5,000 miles and during any scheduled tire rotations.

What is the torque on a 2008 Honda Fit wheel?

The 2008 Honda Fit wheel torque specification is 80 ft-lbs (108108108 N·m). When tightening, use a torque wrench and follow a star or criss-cross pattern to ensure even pressure and prevent damage to the wheel and rotors.
 
This video demonstrates how to use a torque wrench to tighten lug nuts: 59sFamily HandymanYouTube · Jun 27, 2017

• Torque: 808080 ft-lbs (108108108 N·m).
• Tightening pattern: Use a star or criss-cross pattern.
• Tool: Use a calibrated torque wrench.
• Recommendation: Re-torque the lug nuts after about 252525 miles, especially if the wheels are aluminum. 

You can watch this video to learn how to properly torque wheel lug nuts: 58s2CarProsYouTube · Feb 1, 2017

What is the torque on Honda lug nuts?

The recommended lug nut torque for most Honda vehicles is 80 ft-lbs (108 Nm). However, it's crucial to consult your owner's manual to confirm the exact specification for your model and year, as there might be slight variations.

What is the torque for lug nuts on a Honda Fit?

The correct torque for a Honda Fit lug nut is 80 ft-lbs (108108108 N·m). You should tighten the lug nuts in a star or criss-cross pattern with a calibrated torque wrench to ensure even pressure and prevent damage to the studs or rotors. 
This video demonstrates how to replace a lug nut on a Honda Fit: 1mTRQYouTube · Jun 28, 2022
Torqueing your lug nuts

• Set your torque wrench: Adjust a calibrated torque wrench to 808080 ft-lbs (108108108 N·m). 
• Tighten in a star pattern: Tighten each lug nut in a star or criss-cross pattern to ensure the wheel is seated evenly against the hub. 
• Follow up: After tightening, go around the star pattern a second time to confirm all nuts are at the correct torque. 
• Retorque after a short drive: It is recommended to re-check the torque after driving the vehicle for 50-100 miles to ensure the nuts have not loosened.