What is the torque on the 2024 Ford Bronco lug nut?
The lug nuts on the 2024 Ford Bronco are typically torqued to 110 ft-lbs (150 Nm) for factory wheels. Always verify the exact setting for your wheel size and lug nut seat type on the vehicle’s door jamb label or in the owner’s manual, and re-torque after wheel changes or service.
Context and what to expect
Understanding lug nut torque is essential for safe wheel seating and proper clamping force. While Ford commonly specifies 110 ft-lbs for many Bronco configurations, the exact value can vary with wheel size, aluminum versus steel construction, and the lug nut seat type. Always confirm the precise specification for your setup from official documentation.
Standard lug nut torque for the 2024 Bronco
The official Ford specification for most 2024 Bronco factory wheels is 110 ft-lbs (150 Nm). This value assumes standard lug nut seats and typical factory wheels. If you install aftermarket wheels or use different seat types, consult the wheel manufacturer’s instructions and the Bronco owner’s manual for the correct torque setting.
Wheel sizes and lug nut seats
Wheel size and lug nut seat type influence the recommended torque. The Bronco uses a 5-lug pattern with various wheel options; the exact torque can differ based on whether the wheels are steel or alloy and on the seat design (for example, conical vs. ball seats). Always verify your specific configuration.
- Factory configurations with common wheel sizes typically list 110 ft-lbs (150 Nm).
- Aftermarket wheels or lug nuts with different seat types may require a different torque; follow the wheel manufacturer’s instructions and Ford’s guidance.
- Beadlock-enabled or specialized wheels may have separate torque requirements for the lug nuts and any ring bolts or related hardware.
Conclusion: The standard guidance for most Bronco factory wheels is 110 ft-lbs, but always confirm for your exact wheel configuration to avoid under- or over-torquing.
How to properly torque lug nuts on the Bronco
Proper technique ensures even clamping and reduces the risk of wheel loosening or damage. Use a calibrated torque wrench, follow a star-pattern sequence, and avoid lubricating the studs unless the manufacturer specifies otherwise. Recheck torque after wheel work and again after a short drive to ensure the load has settled.
- Park on a level surface, chock the wheels, and raise the Bronco only as needed. Remove the wheel if you’re performing maintenance.
- Inspect studs and wheel mounting surfaces for damage or debris; clean as needed and verify the wheel sits flat against the hub.
- Hand-tighten lug nuts in a star pattern to secure the wheel.
- Using a calibrated torque wrench, tighten each lug nut to 110 ft-lbs (150 Nm) in the same star pattern.
- After installation, re-torque the lug nuts after 50–100 miles (80–160 km) of driving to account for seat settlement and any minor loosening.
Concluding: Adhering to the correct torque and rechecking after initial driving helps ensure wheel security and long-term reliability. If you notice any looseness or unusual vibration, stop driving and re-check or consult a professional.
Summary
The typical lug nut torque specification for the 2024 Ford Bronco is 110 ft-lbs (150 Nm) for factory wheels, though exact values can vary with wheel size and seat type. Always verify on the door jamb label or in the owner’s manual, and re-torque after wheel installation or service. Use a star-pattern tightening sequence and a proper torque wrench to ensure safe, even seating of the wheel.
What is the torque on the 2024 Ford Bronco lug nuts?
The 2024 Ford Bronco lug nut torque is 100 ft-lbs (or 135 Nm) for most standard models, but the Bronco Raptor requires a higher 140 Nm (103.5 ft-lbs). For any 2024 Ford Bronco model, it is critical to use a calibrated torque wrench and tighten the lug nuts in a star pattern. It is also recommended to re-check the torque after about 50–100 miles of driving.
| Model | Torque Specification |
|---|---|
| Most 2024 Ford Broncos | 100 ft-lbs (135 Nm) |
| 2024 Ford Bronco Raptor | 140 Nm (103.5 ft-lbs) |
(this||self).Wufxzb=function(c,e,f,l,k){var d=document.getElementById(c);if(d&&(d.offsetWidth!==0||d.offsetHeight!==0)){c=d.querySelector("div");var g=c.scrollWidth-c.offsetWidth,h=Math.min(e?g:0,g);c.scrollLeft=e&&(l||f)?0:h;var a=d.getElementsByTagName("g-left-button")[0],b=d.getElementsByTagName("g-right-button")[0];a&&b&&(e=RegExp("\\btHT0l\\b"),f=RegExp("\\bpQXcHc\\b"),a.className=a.className.replace(e,""),b.className=b.className.replace(e,""),h===0?a.className="pQXcHc "+a.className:(a.className=
a.className.replace(f,""),k&&c.classList.add("pA30Ne")),h===g?b.className="pQXcHc "+b.className:(b.className=b.className.replace(f,""),k&&c.classList.add("FpCCub")),setTimeout(function(){a.className+=" tHT0l";b.className+=" tHT0l"},50))}};}).call(this);(function(){var id='_d9MlafShJ-qzi-gP-tyz6AM_113';var rtl=false;var gecko=false;var edge=false;var soh=false;
(this||self).Wufxzb(id,rtl,gecko,edge,soh);})();
You can watch this video to learn how to torque lug nuts correctly on a Ford Bronco: 55sBronco BebopYouTube · Apr 15, 2023
- Use a calibrated torque wrench: This ensures the nuts are tightened to the correct specification.
- Tighten in a star pattern: This is crucial for evenly distributing pressure and preventing warping of the brake rotors.
- Re-check after driving: After the first 50 to 100 miles, it's important to re-torque the lug nuts to ensure they haven't loosened.
- Consult the owner's manual: The most accurate torque specifications can always be found in your vehicle's owner's manual.
What is the Ford Bronco's torque?
The standard 2.3-liter EcoBoost I-4 engine outputs 300 horsepower and 325 pound-feet of torque with premium fuel, a substantial amount of power for a standard powertrain.
What to torque Ford Bronco tires to?
Proper torque application is crucial for safely operating your Ford Bronco. The recommended torque specification for most models is 113 Nm (83.3 ft-lb). However, the Bronco Raptor requires a higher torque of 140 Nm (103.5 ft-lb) due to its demanding performance capabilities.
What is the torque spec for the 2024 Bronco sport?
The standard engine is a 1.5-liter EcoBoost® four-cylinder that produces 181 horsepower and 190 lb-ft of torque, but you can also opt for a 2.0-liter version that instead makes 250 horsepower alongside 277 lb-ft of torque.
