What is the torque specs for the brake caliper on a 2010 Dodge Ram 3500?

For a 2010 Ram 3500 equipped with front disc brakes, the caliper mounting bolts to the caliper bracket should be torqued to 20-25 ft-lbs (27-34 Nm); the caliper bracket bolts to the knuckle should be torqued to 95-110 ft-lbs (128-149 Nm); and the brake hose banjo bolt to the caliper should be 25-30 ft-lbs (34-41 Nm). These figures can vary with different brake hardware and vehicle options, so always verify with the factory service manual for your exact VIN.

Front brake caliper torque specifications

The following values apply to the front brake caliper assembly on most 2010 Ram 3500s with factory front discs. They cover the primary fasteners involved when assembling or reassembling the caliper and rotor system.

• Caliper mounting bolts (caliper to brake caliper bracket): 20-25 ft-lbs (27-34 Nm)


• Caliper bracket bolts (bracket to knuckle): 95-110 ft-lbs (128-149 Nm)


• Brake hose banjo bolt (hoses to caliper): 25-30 ft-lbs (34-41 Nm)

In practice, technicians often target the midpoints of these ranges to ensure even seating and prevent movement under braking. Always torque in a crisscross pattern where applicable and recheck after initial torqueing to account for any bolt stretch or thread condition.

Rear brakes and related considerations

On most 2010 Ram 3500 configurations, the rear brakes are drum-type and do not involve a brake caliper or caliper bolts. If you encounter a rare rear-disc setup or a special option, the caliper torque values would resemble the front-disc pattern, but always confirm with the vehicle’s service manual and VIN-specific documentation.

Why these specs matter

Correct torque on caliper-related fasteners ensures proper caliper alignment, effective wheel cylinder or pad contact, and a reliable seal against fluid leaks. Under-torqued fasteners can lead to caliper movement, brake noise, or safety concerns, while over-torqued bolts risk thread damage or caliper misalignment.

Maintenance tips and verification

Always use fresh fasteners when reassembling brake components, replace any damaged bolts, and follow the manufacturer’s lubrication guidelines for sliding pins and related hardware. If you’re unsure about the exact torque for your VIN or if aftermarket components are installed, consult the Mopar service manual or an authorized dealer for precise specifications.

Summary

The key front-brake torque values for a 2010 Dodge Ram 3500 are: caliper mounting bolts to the bracket 20-25 ft-lbs, bracket bolts to the knuckle 95-110 ft-lbs, and the brake hose banjo bolt 25-30 ft-lbs. Rear brakes on this model are typically drum-type and do not use caliper bolts. Always verify with the official service documentation for your exact vehicle configuration.

What is the torque spec for brake caliper bolts?

Torque specs for brake caliper bolts vary significantly depending on the vehicle, but here are some general guidelines: caliper mounting or bracket bolts are typically 70–100 ft-lbs, while caliper slide/guide pin bolts are often 18–35 ft-lbs. Always use your vehicle's specific service manual for the correct values, as they are crucial for safety. 
Caliper mounting/bracket bolts

• What they do: These bolts attach the caliper bracket to the wheel knuckle or spindle. 
• General torque range: 707070 to 100 ft-lbs100 ft-lbs100 ft-lbs. 
• Example: A 2003 Silverado specifies 85−95 ft-lbs85 minus 95 ft-lbs85−95 ft-lbs for caliper bracket bolts. 

Caliper slide/guide pin bolts

• What they do: These bolts hold the caliper to the bracket and allow it to slide to center itself on the rotor. 
• General torque range: 181818 to 35 ft-lbs35 ft-lbs35 ft-lbs. 
• Example: A 2011 Honda Accord specifies 17 ft-lbs17 ft-lbs17 ft-lbs for the rear and 37 ft-lbs37 ft-lbs37 ft-lbs for the front guide pin bolts. 

Other brake-related bolts

• Banjo bolt (brake line to caliper): Torque to about 18 ft-lbs18 ft-lbs18 ft-lbs.
• Bleeder screw: Torque to a low value, around 8 ft-lbs8 ft-lbs8 ft-lbs. 

Important considerations

• Always use the service manual: Torque specifications are not universal and must be obtained from your specific vehicle's service manual for safety. 
• Two types of bolts: Be sure to differentiate between the larger caliper mounting/bracket bolts and the smaller caliper slide/guide pin bolts, as they have very different torque values. 
• Use a torque wrench: Using a torque wrench is essential for ensuring the bolts are tightened to the correct specification. 
• Clean and lubricate: Clean threads before applying new bolts and lubricate slide pins with the manufacturer-specified grease to prevent sticking. 

What is the torque spec of the Dodge Ram 3500?

Torque specs for a Ram 3500 depend on the engine and model year, but commonly range from 429 lb-ft for the 6.4L HEMI V8 to 1,075 lb-ft for the high-output 6.7L Cummins turbo diesel. Standard torque for the 6.7L Cummins diesel is 850 lb-ft. 
Engine torque specifications

• 6.4L HEMI V8 (Standard): 429 lb-ft
• 6.7L Cummins Turbo Diesel (Standard): 850 lb-ft
• 6.7L High-Output Cummins Turbo Diesel (Available): 1,075 lb-ft 

Other specific torque applications

• Wheel hub nut: For a 2017 Ram 3500 DRW, the hub nut torque is approximately 260-300 ft-lbs. 
• Hub assembly bolts (2007): For a 2007 6.7L Cummins, hub assembly bolts are around 130-150 ft-lbs. 
• Axle nut (2007): For a 2007 6.7L Cummins, the axle nut is around 450 ft-lbs. 

Note: Torque specifications can vary significantly based on the model year and specific component. Always refer to your vehicle's owner's manual or a reliable service manual for the most accurate information for your specific truck.

What is the torque on the brake caliper bolts on a 2012 Dodge Ram 3500?

The torque specifications for the light-duty package are 130 ft/lbs for the front caliper brackets and 120 ft/lbs for the rear caliper brackets. The heavy-duty front brake caliper bracket has a torque specification of 275 ft/lbs.

What is the torque specs for the brake caliper on a 2011 Dodge Ram 2500?

The torque specifications for the light-duty package are 130 ft./lbs. for the front caliper brackets and 120 ft./lbs. for the rear caliper brackets. The heavy-duty front brake caliper bracket has a torque specification of 275 ft./lbs.