What kind of oil does a 4.6 crown Vic take?
The recommended oil for a 4.6-liter Ford Crown Victoria is 5W-30 motor oil. This is the standard oil weight and type specified by Ford for this engine size and model.
Detailed Explanation
The Ford Crown Victoria is a full-size sedan that was produced from 1992 to 2011. The 4.6-liter V8 engine was a common powertrain option for this vehicle. When it comes to the recommended motor oil, Ford specifies the use of 5W-30 oil for this engine.
The 5W-30 oil weight provides the right balance of cold-weather fluidity and hot-weather viscosity for the 4.6L V8. This oil weight is designed to flow easily when the engine is cold, aiding in quick lubrication on startup. At the same time, it maintains sufficient thickness when the engine reaches normal operating temperatures to protect critical components like the crankshaft, camshaft, and pistons.
Key Reasons for 5W-30 Oil
- Viscosity: The 5W-30 viscosity is well-suited for the 4.6L V8 engine, providing the right balance of flow and protection across a wide temperature range.
- Manufacturer Recommendation: Ford specifically calls for 5W-30 oil in the owner's manual and service information for the Crown Victoria with the 4.6L engine.
- Engine Design: The 4.6L V8 was engineered by Ford to operate optimally with 5W-30 motor oil, which helps ensure proper lubrication and wear protection.
- Fuel Economy: The lower viscosity of 5W-30 oil can contribute to slightly improved fuel economy compared to heavier 10W-30 or 10W-40 oils.
Following Ford's recommended 5W-30 oil specification is important to maintain the engine's performance and longevity. Using the right oil weight and type helps ensure the 4.6L V8 in your Crown Victoria receives the proper lubrication and protection it needs.
What kind of oil does a 2007 Grand Marquis 4.6 take?
5W-20
How much oil does a 2007 Ford Crown Victoria 4.6 take?
Capacity: 6 quarts (with filter). After refill check oil level.
How much oil does a 2000 Crown Vic 4.6 take?
5 quarts
Capacity: 5 quarts (with filter).
How much oil does a 4.6 L v8 take?
6 quarts (with filter). When refilling, remove dipstick to provide adequate venting and allow oil to flow into crankcase. After refill, check oil level.
Is it better to use 5w20 or 5W30?
Typically, a 5W-20 oil provides higher gas mileage than a 5W-30 due to its more effortless flow. However, the 5W-30 oil is still a suitable option where fuel efficiency is concerned. Using 5W-30 simply produces a bit less economy because moving an oil that is less freely flowing through the system consumes more energy.
What oil does a 4.6 crown Vic take?
AMSOIL OE 5W-20 100% Synthetic Motor Oil.
How much horsepower does a 4.6 Crown Vic engine have?
227 HP
FORD Crown Victoria 4.6L V8 4AT RWD (227 HP)
| ENGINE SPECS - 4.6L V8 4AT RWD (227 HP) | |
|---|---|
| Power: | 167 KW @ 4800 RPM 227 HP @ 4800 RPM 224 BHP @ 4800 RPM |
| Torque: | 272 lb-ft @ 4000 RPM 369 Nm @ 4000 RPM |
| Fuel System: | Electronic Injection |
| Fuel: | Gasoline |
What oil does a 2000 Ford 4.6 take?
5W-20
5W-20 (All TEMPS) - This specification has been updated from 5W-30 to 5W-20 per a Technical Service Bulletin from the manufacturer 5W-20 is the preferred viscosity. Capacity: 6 quarts (with filter).
