What kind of transmission fluid does a 2014 Ford Explorer take?
The 2014 Ford Explorer requires a specific type of transmission fluid to ensure proper operation and longevity of the vehicle's transmission. According to the manufacturer's recommendations, the 2014 Ford Explorer should use Motorcraft MERCON LV automatic transmission fluid.
Transmission Fluid Type
The 2014 Ford Explorer is equipped with a 6-speed automatic transmission. Ford specifies that this transmission requires the use of Motorcraft MERCON LV fluid. MERCON LV is a specialized low-viscosity automatic transmission fluid designed for use in Ford, Lincoln, and Mercury vehicles with 6-speed and newer automatic transmissions.
Fluid Capacity
The total transmission fluid capacity for a 2014 Ford Explorer is approximately 9.5 quarts (9 liters). However, the exact fluid capacity may vary slightly depending on factors such as the specific model, engine, and whether the vehicle has a tow package installed. It's always best to refer to the owner's manual or contact a Ford dealer for the most accurate fluid capacity information for a particular 2014 Ford Explorer.
Fluid Change Interval
Ford recommends changing the transmission fluid in a 2014 Ford Explorer every 30,000 miles (48,000 km) or 2 years, whichever comes first. Proper maintenance of the transmission fluid is crucial to ensure the smooth and reliable operation of the vehicle's transmission.
Fluid Replacement Procedure
- Locate the transmission fluid drain plug, usually located at the bottom of the transmission housing.
- Place a drain pan underneath to catch the old fluid.
- Unscrew the drain plug and allow the old fluid to drain completely.
- Once drained, replace the drain plug and tighten it securely.
- Locate the transmission fluid fill plug, usually on the side of the transmission housing.
- Slowly pour in the new Motorcraft MERCON LV fluid until it begins to drip out of the fill plug.
- Replace the fill plug and tighten it securely.
- Start the engine and let it idle for a few minutes to circulate the new fluid.
- Check the fluid level and top up if necessary, following the instructions in the owner's manual.
It's important to use the correct type and amount of transmission fluid to maintain the health and performance of the 2014 Ford Explorer's transmission. Consult a professional mechanic if you are unsure about any part of the fluid replacement process.
How much transmission fluid does a Ford Explorer take?
Capacities and Specifications
| Item | Capacity |
|---|---|
| Rear differential fluid. | 28.07 ± 1.01 fl oz (830 ± 30 ml) |
| Power Transfer Unit (PTU) fluid. | 12.7 ± 1.7 fl oz (375 ± 50 ml) |
| Automatic transmission fluid. | 12.15 qt (11.5 L)1 |
| Windshield washer fluid. | Fill as required |
Does it matter what transmission fluid I use?
Choosing the correct transmission fluid is critical to insuring the maximum performance and fuel economy from your car.
What transmission fluid does a 2014 Ford Explorer take?
FRAM – Full Synthetic Dexron VI Automatic Transmission Fluid: 1 Quart (Part No. F426)
How much does a new transmission cost for a 2014 Ford Explorer?
2014 Ford Explorer Transmission Cost
The cost of a new 2014 Ford Explorer transmission could be over $3,500 depending on the vehicle, however, transmission services such as fluid changes and a transmission fluid flush are considerably less expensive, in some cases costing less than $150.
What type of transmission does a 2014 Ford Explorer have?
All three engines are paired with a six-speed automatic transmission.
How often should you change transmission fluid 2014 Ford Explorer?
If you don't routinely change your fluids at least every 30,000 miles or so, you may find that your 2014 Ford Explorer transmission will slip.
What transmission fluid does Ford recommend?
MERCON® transmission fluids undergo extensive testing, both in the lab and in real-world conditions, to ensure they provide optimum performance and durability. MERCON® fluids are the only fluids approved by Ford Motor Company for their recommended application.
How many quarts does a 2014 Ford Explorer take?
Oil Grade: SEO18
| Viscosity: | 5W-20 (All TEMPS) |
|---|---|
| Capacity: | 6 quarts (with filter). After refill check oil level. |
| Torque: | 20 ft/lbs (Oil Drain Plug) |
Can you use dexron VI in a Ford?
KLONDIKE DEXRON®-VI / MERCON® LV Full Synthetic Automatic Transmission Fluid is a highly advanced, premium low viscosity automatic transmission fluid designed for use in vehicles manufactured by General Motors and Ford where DEXRON®-VI and/or MERCON® LV fluids are specified.
Can I use MERCON v instead of mercon atf?
“All transmissions which recommended using MERCON ATF can now be serviced with MERCON V,” said Ron Romano, FCSD Service Lubricants Technical Expert. “MERCON V is a tighter specification which delivers better anti-oxidation, anti-wear and anti-shudder properties.
