What part number is MAF sensor Subaru?
The part number for a Subaru Mass Air Flow (MAF) sensor can vary depending on the specific model and year of your Subaru vehicle. To determine the correct part number, you'll need to provide details about your Subaru, such as the model, engine size, and production year.
Locating the MAF Sensor Part Number
The MAF sensor is a critical component in your Subaru's engine management system, responsible for measuring the amount of air entering the engine. To find the part number for your Subaru's MAF sensor, you can follow these steps:
- Locate the MAF sensor in your Subaru's engine bay. It is typically located near the air intake system.
- Inspect the MAF sensor for any part numbers or identifying information printed on the sensor itself.
- Check your Subaru's owner's manual or service documentation for the specific part number of the MAF sensor.
- If you can't find the part number on the sensor or in your vehicle's documentation, you can use an online parts lookup tool or contact your local Subaru dealer for assistance.
Once you have the part number, you can use it to order a replacement MAF sensor or verify that you have the correct one for your Subaru.
Importance of Replacing the MAF Sensor
The MAF sensor is a critical component in your Subaru's engine management system, and a faulty or failing sensor can cause a range of issues, including reduced fuel efficiency, engine performance problems, and even the illumination of the check engine light. Replacing the MAF sensor with the correct part number is essential for maintaining the proper operation of your Subaru's engine.
What map system does Subaru use?
Get started with your Starlink® Navigation System
Your new Subaru STARLINK® comes equipped with an integrated navigation system, powered by TomTom. You will benefit from the state-of-the-art navigation technology and optimized mapping routes to guide you on safer, better and, ultimately, more enjoyable journeys.
What code is the MAP sensor?
The P0105, P0106, P0107, P0108, and P0109 codes all indicate some kind of issue with the Manifold Absolute Pressure sensor, which is also called the MAP sensor, the Barometric Pressure Sensor, or the Baro Sensor. This sensor measures your intake manifold pressure or atmospheric pressure.
What is the code for the MAF sensor on a Subaru?
A P0101 OBD-II trouble code is one of many diagnostic trouble codes (DTCs) that can be detected by an onboard diagnostic system within your vehicle. This particular code is set when the engine control module (ECM) detects an issue with the mass airflow (MAF) sensor within your vehicle.
How do I get activation code for Subaru map update?
Go to Settings, Navigation, Map Update Information and take note of the “request code”.
Do you have to pay for a Subaru map update?
Your vehicle manufacturer – Subaru - provides 3-years of free map update commencing your vehicle purchase. In case of concern, we recommend you consult your vehicle retailer.
Where is the part number on a mass air flow sensor?
Part number location
The air flow meter, mass air flow sensor or maf is located in the engine compartment usually adjacent to the air filter assembly. The part numbers that you need are located on the outside of the housing/tube. Pierburg mostly start with 7.
How much does it cost to update the map on a Subaru?
Subaru Map Update Toolbox - is a free-of-charge software that allows you to purchase, download, and install map updates onto/update your navigation micro-SD card. Without the Toolbox, you cannot download updates to your navigation micro-SD card. Download the Toolbox here.
Who makes Subaru MAF sensors?
DENSO is the OE manufacturer for Subaru but I would be weary of using the non Subaru branded MAF. Mine had died at 175K and i put the DENSO one in.... I found the original MAF sensor from my 2014 Legacy 2.5i and verified same part number. Installed it and instant improvement in engine fuel consumption.
What is the part number for the Subaru MAP sensor?
M.A.P Sensor - Subaru (22627AA560)
2.4L turbo.
How can I update MySubaru maps for free?
Open the SUBARU STARLINK app on your smartphone. 2. Then, connect your smartphone to your vehicle 3. Select “Settings” > “Navigation” > “Map Update” > “Check for Updates”.
