What size is the bolt on a 2009 Honda Accord tensioner?
As a car owner, knowing the specifications of your vehicle's components can save you time and money during maintenance and repairs. One common question among Honda Accord owners is about the bolt size for the tensioner. This article will provide you with the necessary details to help you with your vehicle's maintenance.
What is a Tensioner?
The tensioner is a crucial component in your vehicle's engine that maintains the proper tension on the serpentine belt. This belt is responsible for powering various accessories in your car, such as the alternator, power steering pump, and air conditioning compressor. A properly functioning tensioner ensures that these components operate smoothly and efficiently.
Bolt Size for the 2009 Honda Accord Tensioner
For the 2009 Honda Accord, the bolt size for the tensioner is typically 10mm. This size is standard for many Honda models, but it's always a good idea to double-check your specific vehicle's manual or consult with a professional mechanic to confirm the exact specifications.
Steps to Replace the Tensioner
If you're considering replacing the tensioner yourself, here are the general steps you should follow:
- Gather Tools: Ensure you have a 10mm socket, ratchet, and any other necessary tools.
- Disconnect the Battery: Always disconnect the negative terminal of the battery before starting any repair work.
- Remove the Serpentine Belt: Use a wrench to relieve tension on the tensioner and slide the belt off.
- Unbolt the Tensioner: Use the 10mm socket to remove the bolts securing the tensioner in place.
- Install the New Tensioner: Position the new tensioner and secure it with the bolts.
- Reinstall the Serpentine Belt: Follow the belt routing diagram to ensure proper installation.
- Reconnect the Battery: Finally, reconnect the battery and start the engine to check for proper operation.
Following these steps can help you successfully replace the tensioner in your 2009 Honda Accord. However, if you're unsure or uncomfortable with any part of the process, it's always best to consult a professional mechanic.
Conclusion
Understanding the specifications of your vehicle, such as the bolt size for the tensioner, is essential for effective maintenance. For the 2009 Honda Accord, a 10mm bolt is required for the tensioner. Whether you're a DIY enthusiast or prefer to leave repairs to the professionals, having this knowledge can enhance your car maintenance experience.
Frequently Asked Questions
What size bolt for 2009 Honda Civic belt tensioner?
Detailed Notes: Socket bolt 10x59x1. 25mm.
What size tool socket is used for the serpentine belt removal tool on the tensioner?
A 3/4 inch socket fits perfectly in the serpentine tensioner.
What size is the bolt on a 2010 Honda Accord tensioner pulley?
Attached to the tensioner is a 19mm bolt, that is the correct one.
What tool do I need to loosen a belt tensioner?
You may need a special tool, but many spring tensioners have a square hole, for a 3/8” or 1/2” breaker bar, or a hex or square protrusion for a wrench or socket. Using the appropriate tool, release tension on the belt. You'll need to hold some spring tensioners while slipping on a new belt.
What tools do I need for a serpentine belt?
Tools/Supplies Needed:
- ratchet and socket set.
- torque wrench.
- new replacement belt.
- new tensioner.
- new pulley.
- wrench set.
- jack and axle stands or ramps.
How to remove tensioner pulley bolt?
I'm gonna go and loosen. It I get down in here loosen that holy pull the bolt out. And then pull the pulley off.
What size is the nut on the idler pulley?
It is an M10-1.25 flat faced flange nut.
What tools do I need to change a tensioner pulley?
These are all the tools you need to do job you know ratchet fifteen millimeter socket the new pulley. And a pulley tensioner bar to relieve the tension of the belt.
What size is the tensioner pulley bolt?
The bolt is a 15 mm and if it has been replaced it may be a 13mm. I usually don't use the bolt but carefully pry the tensioner back to release the belt while a helper removes the belt from one pulley. Reverse the procedure to install the belt.
What size wrench do I need to replace a serpentine belt?
Use a 17mm wrench to pull the tension back, then tighten the 13mm bolt which locks the slotted portion in the bracket. Remove the belt, this can be tricky if you are working with an inline drivetrain that is equipped with a mechanical fan.
