What size is the wheel nut on a 2007 Toyota Corolla?
The wheel lug nuts on a 2007 Toyota Corolla are M12 x 1.5 with a 21 mm hex socket and a 60-degree conical seat, used on the stock 5-lug setup. The factory torque specification is about 76 ft-lbs (103 Nm).
Core specifications
Below are the standard specifications you’ll typically find on the Corolla’s factory wheel hardware. This section covers the common setup for the original equipment wheels.
- Wheel lug pattern: 5x100 mm
- Thread size: M12 x 1.5
- Stud diameter: 12 mm
- Zinc/plated lug nuts: standard on factory wheels
- Nut seat: 60-degree conical (acorn) seat
- Nut outer hex size: 21 mm
- Number of lug nuts per wheel: 5
- Recommended torque (factory spec): 76 ft-lbs (103 Nm)
These specs are standard for the stock wheels on a 2007 Corolla. If you’ve upgraded to aftermarket wheels or a different trim with unique hardware, verify the exact specifications with the wheel manufacturer or a service manual.
Verification and variations
Before you work on wheels or buy replacement lug nuts, it’s important to confirm the correct size for your specific setup, especially if aftermarket wheels are installed.
- Check the vehicle’s owner’s manual or a Toyota service manual for the exact torque specification and lug nut size for your wheel size and trim.
- Inspect the existing lug nuts to confirm the thread size, seat type, and hex size. If the existing nuts fit a 21 mm socket, they are likely the standard size.
- For aftermarket wheels, verify the lug nut dimensions (thread pitch, seat type, and hex size) with the wheel manufacturer and ensure the lug nuts are compatible with your studs and hub.
- When reinstalling wheels, re-torque to the specified value after the initial drive (often within 50-100 miles) to account for seating.
If you’re unsure, consult a Toyota dealer or an ASE-certified mechanic to prevent improper seating or under/over-torque, which can compromise wheel safety.
Summary
For a 2007 Toyota Corolla, use lug nuts with an M12 x 1.5 thread, 60-degree conical seat, and a 21 mm hex, on a 5x100 mm bolt pattern. The recommended factory torque is 76 ft-lbs (103 Nm). Always confirm with your manual or wheel manufacturer if you’ve added aftermarket wheels, and re-torque after installation for safety and proper seating.
What size are the lug nuts on a 2008 Toyota Corolla?
M12 X 1.5
Product specifications
| Fastener Type | Wheel |
|---|---|
| Thread Size | M12 X 1.5 |
| Exterior Finish | Chrome |
| Color | Chrome |
| Thread Style | Right Hand |
What size socket for Toyota Corolla lug nuts?
The socket size for a Toyota Corolla lug nut is 21mm or 13/16 inch. The lug nuts have a metric thread size of M12x1.5mm.
- Socket Size: 212121 mm or 13/1613 / 1613/16 inch
- Thread Size: M12 x 1.51.51.5 mm
What size are the lug nuts on a 2007 Toyota Corolla?
The 2007 Toyota Corolla lug nut size is M12x1.5, and a 13/16-inch or 21mm socket is used to remove it. You should also confirm the fitment with the wheel's specific lug nut seat, as it can affect the correct nut style and length.
Lug nut specifications
- Thread Size: M12x1.5
- Socket Size: 13/16 inch or 21mm
- Seat Style: Typically conical or acorn, but it's best to verify with your specific wheel
What size are Toyota Corolla wheel nuts?
The standard Toyota Corolla lug nut size is M12x1.5mm. The correct lug nut must match the vehicle's wheel studs, and you may need a 21mm (or 13/16 inch) socket to tighten them.
- Thread Size: M12x1.5mm
- Socket Size: 21mm (or 13/16 inch)
- Important: Always confirm the specific lug nut type (like acorn, mag, etc.) and seat style needed for your vehicle's wheels before purchasing, as the mating surface is critical for a proper and safe fit.
