What size socket is the axle nut on a 2011 Toyota Camry?
The axle nut on a 2011 Toyota Camry typically requires a 32mm socket to remove. This is a standard size for the rear axle nut on this model year of the popular midsize sedan.
Detailed Explanation
The 2011 Toyota Camry is equipped with a rear axle assembly that uses a large nut to secure the axle shaft in place. This nut is responsible for holding the rear wheel hub and bearing assembly onto the vehicle. Properly tightening and torquing this nut is crucial for safe and reliable operation of the Camry's rear suspension and drivetrain.
According to the Toyota service and repair manuals, the recommended socket size for the 2011 Camry's rear axle nut is 32mm. This is a fairly large socket, as the nut needs to be able to withstand the high torque loads placed on it during normal driving conditions and when the vehicle is under load.
It's important to use the correct 32mm socket when servicing the rear axle on a 2011 Toyota Camry. Using the wrong size tool could result in damage to the nut or axle shaft, leading to potential safety issues and expensive repairs. Always refer to the manufacturer's recommended specifications when performing maintenance or repairs on your vehicle.
Key Points:
- Axle Nut Size: 32mm
- Vehicle Model: 2011 Toyota Camry
- Purpose: Secures the rear wheel hub and bearing assembly
- Importance: Proper tightening is crucial for safe and reliable operation
- Recommendation: Always use the manufacturer-specified 32mm socket
Properly maintaining the rear axle components on your 2011 Toyota Camry is essential for ensuring the vehicle's safety and performance. Be sure to use the correct 32mm socket when servicing the axle nut to avoid any potential issues.
What size is the axle nut socket on a 2013 Toyota Corolla?
It is 36. And you dont need to remove the axle nut to get the rotor off.
What size is the axle nut on a 2011 Toyota Camry?
The axle nut is 30mm 12 point. You will need a Deep 30mm 12 point socket. Alternative deep sockets that will work are a deep 33mm 6 point and a deep 1 3/16" 12 point.
What size socket is a Toyota wheel nut?
What are Toyota Lug nuts sizes? The lug nuts on a Toyota vehicle are metric and 21mm in size. You can use a 13/16″ socket to fit them, but only if the tin cover is not damaged or bent. The thread size of the lug nuts on a Toyota Camry is M12 x 1.5, and the center hole size is 60.1 mm.
What size is a wheel nut socket?
Sizes: 18.5, 19.5mm single Hex (6pt) x 1/2"D x 78mm long. Thin walled sockets with protective sleeve to prevent damage to alloy wheels.
What size socket do I need to remove wheel nuts?
If the question “what size of sockets for lug nuts should I use” comes to your mind; the most common socket sizes for lug nuts are 17 mm, 19 mm, 21 mm, and 22 mm, all available at Olsa Tools. The 11/16-inch, 3/4-inch, 13/16-inch, and 7/8-inch SAE socket sizes also are fairly common.
What size socket is a Toyota axle nut?
39650 39mm 12 pt Axle Nut Socket for Toyota.
What size socket is needed to remove a CV axle?
36mm is correct. Make sure it's attached to a decent breaker bar; those things are on there pretty tight.
Is 13 16 the same as 21mm?
You can use a 21mm socket on a 13/16 nut. But not vice versa. And the fitment might not be great (Depends on manufacturing tolerances). 13/16 of an inch is 20.65mm.
What size is the axle nut bolt?
36mm Axle Nut Socket - services many GM, Ford and Chrysler full-size vehicles. 32mm Axle Nut Socket - services late model Honda and Chrysler vehicles. 34mm Axle Nut Socket - services many GM mid-size vehicles. 29mm Axle Nut Socket - services late model GM, Ford and Asian imports.
Do you need a torque wrench for axle nut?
Avoid Overtightening – Use the Right Tool
Many technicians use an impact gun when installing an axle nut on a wheel hub bearing which not only overtightens the bearing but can also cause premature wear to the hub assembly. MOOG recommends using a torque wrench to tighten the axle nut accurately.
