Where is the TPMS button on a Ford F150?

The quick answer: many newer Ford F-150 models don’t have a dedicated TPMS reset button. Instead, TPMS is reset through the vehicle’s settings or automatically after inflating tires and driving. If your truck does have a physical button, it’s typically located in the glove box or on the lower dash near the steering column.

Tire Pressure Monitoring System (TPMS) alerts you to underinflated or overinflated tires and sometimes needs a reset after tire service, rotation, or replacement sensors. Ford’s exact reset method can vary by year and trim, so this guide covers common locations and procedures you may encounter on recent F-150s.

Common locations for a physical TPMS reset button

Not every F-150 includes a physical reset switch. When present, Ford tends to place it where you can reach it from the driver’s seat, and the label is usually “TPMS” or a tire icon.

• Glove box area: Some trims place a small TPMS button on or inside the glove box door or near the latch. Look for a tiny button labeled “TPMS” or with a tire icon.


• Lower dash near the steering column: A few configurations position the reset switch on the lower dash or just to the left of the driver’s knee area for easy access.


• Center console area: In certain layouts, a TPMS button can be found near the USB ports, 12V outlet, or cupholders in the center console.

If you can’t locate a physical button, your vehicle may rely on electronic TPMS reset through the instrument cluster or infotainment system, or it may auto-calibrate after you drive with properly inflated tires.

Resetting TPMS: two main approaches

Ford offers two primary pathways to reset or relearn TPMS on the F-150, depending on whether your model includes a dedicated button or uses the electronic menu. The steps below cover both paths and are common across many recent model years.

• Physical TPMS reset button (if equipped): Turn the ignition to ON (engine off), then press and hold the TPMS button until the TPMS indicator light blinks or confirms the reset. Release the button, then drive to recalibrate the sensors, usually at highway speeds for about 10 minutes.


• Electronic reset via instrument cluster or infotainment: Access Settings on the instrument cluster or the vehicle’s infotainment system, navigate to TPMS or Tire Pressure Monitoring, select Reset or Relearn, and follow the prompts. After the reset, drive at a steady speed (around 50 mph / 80 km/h or higher) for several minutes to allow the system to relearn tire pressures.

Note that the exact wording and path can vary by year and trim. Always inflate tires to the recommended pressures shown on the door jamb placard before attempting a reset. If the warning persists, there may be a faulty sensor, a calibration issue, or a tire leak requiring service.

What to do if the light won’t reset

If the TPMS light remains after following the reset steps, perform these checks to troubleshoot common issues:

• Inflate each tire to the recommended pressure when cold, then recheck with a tire pressure gauge.


• Inspect tires for punctures or slow leaks; repair or replace as needed.


• Check valve stems and sensors, especially after tire rotation or replacement; some sensors may be damaged or aged.


• Consult the owner's manual or a Ford dealer for model-specific relearn procedures or sensor diagnostics if the problem continues.

Drive a short trip after reset to confirm the warning clears; if not, you may need professional diagnostics to identify a faulty sensor or calibration issue.

Summary

Across model years, the Ford F-150 adapts its TPMS reset process. Some trims include a physical TPMS button (often in the glove box or near the dash), but many rely on electronic relearn through the instrument cluster or infotainment system, with recalibration after driving. Always start by inflating tires to the recommended pressure, then follow the appropriate reset method for your specific year and trim. If in doubt, check the owner’s manual or contact a Ford dealer for guidance tailored to your truck.

Where is the TPMS reset button on a Ford f150?

To reset the TPMS on an F-150, you first need to inflate all tires to the correct pressure. Then, enter training mode by turning the ignition to "ON" and pressing the hazard light button six times (or by holding a physical TPMS reset button until the light flashes, depending on your model). Once the horn honks, deflate the front-left tire until it beeps to signal it has been trained, then repeat the process for the other tires in the correct order (front right, rear right, rear left). 
This video shows how to reset the TPMS on an F-150 using the hazard light button: 48sReviews and How To's!YouTube · Jan 12, 2018
Method 1: Using the hazard light button 

1. Inflate all tires to the recommended pressure found on the sticker inside the driver's door jamb. 
2. Turn the key to the "ON" position but do not start the engine. 
3. Press the hazard light button six times within 10 seconds. You should hear the horn honk, and the message center will indicate that it's ready to train the left-front tire. 
4. Deflate the left-front tire until the horn beeps once, which confirms it has been trained. 
5. Repeat the process of deflating the tires for the front-right, rear-right, and rear-left tires in that order. The horn will beep once after each tire is trained. 
6. The message center will display "Training Complete" once all sensors have been trained. 

Method 2: Using a physical reset button

• Some F-150 models have a physical TPMS reset button, often located below the steering wheel.
• To reset using this button:
  1. Turn the ignition key to the "ON" position.
  2. Press and hold the TPMS reset button until the TPMS indicator light on the dashboard blinks slowly three times.
  3. Start the vehicle and allow it to run for about 20 minutes to complete the reset. 

If the light remains on

• Drive the vehicle at speeds above 505050 mph for at least 10 minutes, as some systems will reset automatically after a sufficient driving period. 
• If the problem persists, there may be a faulty sensor that needs to be replaced. In this case, it is best to have the vehicle serviced by a professional, as the tire will need to be removed from the rim to replace the sensor. 

Where is the tire pressure sensor reset button located on a Ford?

The Ford tire pressure sensor reset button is usually located underneath the steering wheel, but the reset procedure can vary by model. Some models have a dedicated physical button, while others use a touchscreen menu on the driver information center or a sequence of button presses. After performing the reset, you will need to inflate your tires to the correct pressure, and sometimes a short drive is necessary for the system to recalibrate. 
You can watch this video to learn how to reset the TPMS light on a Ford Fusion: 59sThe Driver ModYouTube · Jan 5, 2022
Common reset button location and procedure 

• Location: Look for a button, often labeled "TPMS" or similar, beneath the steering wheel, near the dashboard, or on the driver's side door. 
• Physical button: If you have a dedicated button, turn the key to the "On" position (without starting the engine) and press and hold the button until the TPMS light on the dashboard blinks three times. 
• Touchscreen: On newer models, use the touchscreen to navigate to the "Settings" menu, then find the "Vehicle" or "Tire Pressure" settings to find the reset option. 

Alternative reset procedures

• Button sequence: Some Fords require a specific sequence of button presses. For example, a common method involves pressing the brake pedal for three seconds, then pushing the start button three times, leaving it on the third time. 
• Hazard lights: For some models, you can initiate the reset by turning the ignition to the "On" position and then pressing the hazard light button three or six times until you hear a beep. 

After the reset

• Add air to tires: Inflate all tires to the recommended pressure, plus about 333 PSI over the recommended amount. 
• Drive the vehicle: In some cases, you will need to drive for a few minutes at a speed above 202020 mph to allow the system to recalibrate. 

This video demonstrates how to reset the TPMS light using the hazard lights button on a 2020 Ford Transit: 54sTry it yourselfYouTube · Dec 14, 2022
If you still have problems

• Consult your owner's manual for the exact reset procedure for your vehicle. 
• If the light remains on, have a dealership or mechanic check the system, as there could be a sensor failure. 

How to put Ford into TPMS mode?

Ford TPMS Sensor Training

1. Turn the ignition to the OFF position.
2. Turn the ignition to the RUN position three times, ending in the RUN position.
3. Press and hold the brake pedal.
4. Turn the ignition switch to the OFF position.
5. Turn the ignition switch to the RUN position three times, ending in the RUN position.

Where is the TPMS button located?

The TPMS (Tire Pressure Monitoring System) reset button is most commonly located under the steering wheel, to the left of the steering column. However, the exact location can vary, so also check your glove box or within the media center/touchscreen display. The button may also be found on the driver's side of the dashboard. 
You can watch this video to see how to reset the TPMS on a Toyota Tacoma: 1mApple DrainsYouTube · Mar 21, 2021

• Near the steering wheel: Look for a button with a symbol that resembles a tire with an exclamation mark inside it, usually on the left side of the steering column. 
• Glove box: Some models have the button located inside the glove box. 
• Dashboard/center console: Check the driver's side of the dashboard or look for an option within the vehicle's infotainment or touchscreen system, says this YouTube video. 
• Consult the owner's manual: If you still can't find it, your vehicle's owner's manual will have the definitive answer.