Where is the TPMS button on a Ford Transit?

The TPMS button on a Ford Transit isn’t fixed to one spot across all model years. Some Transits have a dedicated reset switch, while others rely on automatic relearning after tire pressures are corrected. In some trims there may be no separate button at all, with reset handled through the instrument cluster or not requiring a manual reset.

This guide explains where to look for a TPMS reset control on various Transit generations, how to use it if present, and what to do if you can’t locate a button or the light won’t reset. Always consult your vehicle’s manual or a Ford service representative for the exact procedure for your year and trim.

Common locations by generation

Ford has placed TPMS reset controls in a few predictable spots depending on the year and trim. Check these areas first:

• Glove box area: Some Transits hide a small TPMS/RESET button on the glove box lid or inside the glove box itself, often near the side panel or edge.


• Under-dash or knee panel (driver’s side): A removable cover or small circular button near the left-hand side of the steering column or the hood release lever can conceal the reset control.


• Instrument cluster/menu button (modern models): In newer Transits, the reset option may appear as a setting in the instrument cluster or infotainment/vehicle settings rather than a separate physical button.


• Center console area: Some trims place a TPMS button near the center console storage or cupholder area, sometimes under a small cover.

Because the TPMS reset control location varies by model year and trim, it’s best to verify the exact spot for your specific Transit in the owner’s manual or with a Ford dealer.

How to reset TPMS when there is a button

If you locate a dedicated TPMS/RESET button, follow these general steps. Note that the exact sequence can vary by year, so refer to the manual if available.

1. Inflate all tires to the recommended cold pressure shown on the door placard.


2. Turn the ignition to the ON position (do not start the engine).


3. Press and hold the TPMS/RESET button until the TPMS indicator light in the instrument cluster blinks once and then stays on (or until you hear a confirmation tone, depending on the model).


4. Release the button and drive at a steady speed (typically 30–50 mph) for about 10–15 minutes to allow the system to relearn all tire positions.


5. Check the instrument cluster to confirm the TPMS light has turned off. If it remains on, repeat the process or consult a dealer.

If the light does not reset after following these steps, the issue may be a faulty sensor, a damaged tire, or another fault within the TPMS. A service check is recommended.

What to do if you can’t find a button or the light won’t reset

In some model years there is no dedicated reset button, and the system relearns automatically after tires are inflated to the correct pressure and the vehicle is driven. When in doubt, try these steps:

• Verify every tire—including the spare, if your model uses it—has the correct cold pressure according to the door placard.


• Drive at highway speeds (around 50 mph or more) for 10–15 minutes to allow the system to relearn tire positions.


• If the TPMS light remains on after a reasonable relearn attempt, inspect for slow leaks or damaged sensors and consider scheduling a diagnostic with Ford service.


• Consult the owner’s manual or contact a Ford dealer for model-year-specific instructions, as some Transits use a cluster-based reset or require a professional diagnostic tool.

Persistent TPMS warnings can indicate a faulty sensor, a damaged valve stem, or a leak in one of the tires. A qualified technician can diagnose and replace sensors if needed.

Summary

locating the TPMS reset control on a Ford Transit depends on the year and trim. Look for a dedicated reset button behind a glove box panel, under a dash knee panel, or within the instrument cluster/vehicle settings on newer models. If you locate a reset control, follow the ignition, pressure, and relearn steps as described. If there’s no button or the light stays on after attempting a relearn, verify tire pressures and consider a professional inspection to check sensors and tires.

Do Ford Transits have TPMS?

Tire Pressure Monitoring Sensor - Repair or Replace
If your TPMS sensor has failed or its battery has died, the tire pressure monitoring system warning light will come on. To have your 2022 Ford Transit-350 expertly repaired, count on the experts at your Ford service department to perform necessary repairs.

How to reset TPMS Ford Transit?

To reset the Ford Transit TPMS, inflate all tires to the correct pressure and then enter training mode by cycling the ignition or hazard lights. The exact method depends on your model: 

• Key ignition models: Turn the key to "RUN" 3 times (engine off) and press the brake pedal. Then turn the ignition OFF, and turn it back to "RUN" 3 times. The horn will beep, and you can then use the reset button or the hazard light switch method to train the sensors, typically by releasing air until the horn beeps again for each wheel. 
• Push-button start models: Cycle the push-button start to the Accessory (ACC) mode 3 times, ending in ACC. Turn the ignition off, then press the brake and cycle the push-button start to ACC again 3 times to initiate training mode. A message will appear, and you can then train the sensors. 
• Display audio models: Navigate to Settings > Vehicle > TPMS Calibration on the touchscreen and press Calibrate. Then, you must drive for about 30 minutes to complete the process. 

This video shows how to reset the TPMS on a Ford Transit using the hazard light method: 56sThe OCD RepairmanYouTube · Nov 20, 2023
Before you begin

• Check the driver's side door jamb or your owner's manual for the correct tire pressure for your vehicle.
• Inflate all tires to the recommended pressure, including the spare. 

For models with a key ignition

1. Turn the ignition to the OFF position. 
2. Press and release the brake pedal. 
3. Turn the ignition from OFF to RUN three times within 10 seconds, ending in the RUN position. Do not start the engine. 
4. The horn will beep once to signal that the TPMS relearn mode has been activated. 
5. You will see a message like "TRAIN LEFT FRONT TIRE" on the display. 
6. To train each sensor:
   • Release some air from the left front tire until you hear a horn beep. 
   • Move to the next tire in sequence (right front, right rear, left rear, spare) and repeat the process until the horn beeps again. 
7. After the spare tire is trained, the message will change to "TRAINING COMPLETE," and the light should turn off. 

For models with a push-button start

1. Press the start button once without your foot on the brake, so the vehicle is in ACC mode. 
2. Power off the vehicle by pressing the button once. You will need to do this two more times, ending in ACC mode. 
3. Press and release the brake pedal, then turn the ignition completely off. 
4. Turn the ignition to ACC again, and then power off one more time. Repeat this two more times, ending in ACC mode. 
5. The horn will sound once, and the TPMS telltale will blink once, initiating the training mode. 
6. Follow the on-screen prompts to train each tire by releasing air from the valve stem until the horn beeps. 
7. After the last tire is trained, you will see a "TRAINING COMPLETE" message. 

For models with a display audio system

1. Make sure the vehicle is on and parked with the parking brake set.
2. Press the Home button on the display screen.
3. Touch Settings.
4. Touch Vehicle.
5. Select TPMS Calibration.
6. Touch Calibrate.
7. The calibration process will begin. You will need to drive the vehicle for about 30 minutes at speeds between 30 and 60 mph for it to complete. 

If the light stays on after a reset

• The reset may have failed, which could be due to an inaccurate sensor. 
• You may need to replace the sensor battery if the light is flashing instead of solid. 
• Contact a professional at a service center for further diagnosis. 

Where is the TPMS button located?

The TPMS button location varies by vehicle, but it is commonly found under the steering wheel on the driver's side, inside the glove compartment, or on the center console. In newer cars, the function is often available through the vehicle's infotainment or navigation system's settings menu. You should always consult your owner's manual for the exact location and reset procedure for your specific car. 
You can watch this video to see where the TPMS button is located in a Toyota Tacoma: 1mApple DrainsYouTube · Mar 21, 2021
Common locations

• Under the steering wheel: Look on the dashboard to the left of the steering column for a button labeled with the TPMS symbol. 
• Glove compartment: The button may be located inside the glove compartment on some models. 
• Center console: Check the center console area, which can be a common spot for vehicle control buttons. 
• Infotainment system: Newer vehicles may not have a physical button. Instead, you'll need to navigate through the touchscreen menu. Look for settings related to the vehicle, and then find the TPMS calibration or reset option. 

How to find the exact location

• Check the owner's manual: This is the most reliable method, as it will provide specific instructions for your vehicle. 
• Look for the TPMS icon: The button, if it exists, will usually be labeled with an icon that looks like a tire with an exclamation point inside. 

Where is the TPMS reset button on a 2019 Ford Transit Connect?

When the vehicle is off, turn the key to the “On” position, but don't start the car. Hold down the TPMS reset button until the light blinks three times, then let go. Start the car and give the vehicle about 20 minutes for the sensor to reset. Generally, you'll find the reset button under the steering wheel.