Why is my Chevy remote start not working?
If your Chevy's remote start feature is not functioning as expected, there could be several potential reasons. In this article, we'll explore the common issues that can cause remote start problems and provide troubleshooting steps to help you get your Chevy's remote start back up and running.
Common Reasons for Chevy Remote Start Failure
There are a few key reasons why your Chevy's remote start may not be working:
- Dead or Dying Key Fob Battery - The remote start feature relies on a functioning key fob, and a low battery can prevent the fob from communicating with your Chevy's onboard systems.
- Incompatible or Incorrect Key Fob - Make sure you're using the correct key fob that's programmed to work with your specific Chevy model. Using the wrong fob can cause remote start issues.
- Disabled Remote Start Feature - Your Chevy may have the remote start feature disabled, either by the dealer or through your vehicle's settings. Check your owner's manual or contact your dealer to verify the feature is enabled.
- Wiring or Electrical Issues - Problems with the wiring or electrical components in your Chevy can prevent the remote start from functioning properly. This may require diagnosis by a professional mechanic.
If you've checked these common issues and your Chevy's remote start still isn't working, there may be a more complex problem that requires further diagnosis and repair.
Troubleshooting Steps
Here are some steps you can take to troubleshoot and potentially resolve your Chevy remote start issues:
- Replace the Key Fob Battery - Start by replacing the battery in your Chevy's key fob. This is often the easiest and most common fix for remote start problems.
- Verify Key Fob Compatibility - Ensure you're using the correct key fob that's programmed to work with your specific Chevy model. Consult your owner's manual or contact your dealer if you're unsure.
- Check Remote Start Settings - Refer to your owner's manual or contact your Chevy dealer to confirm the remote start feature is enabled on your vehicle.
- Seek Professional Diagnosis - If the above steps don't resolve the issue, it's best to have a qualified mechanic diagnose and repair any underlying wiring or electrical problems that may be causing the remote start failure.
By following these troubleshooting steps, you should be able to identify and resolve the issue with your Chevy's remote start feature. If the problem persists, don't hesitate to consult a professional for further assistance.
Why won't my Chevy remote start?
The vehicle cannot be remote started if: . The key is in the ignition. . The hood is not closed. . There is an emission control system malfunction and the malfunction indicator lamp is on. . Fuel level is too low. The engine will turn off during a remote vehicle start if: . The coolant temperature gets too high. .
How do I reset my remote starter?
Insert your ignition key and turn it to Accessory (or press the start button once without pushing the brake pedal). Press the Lock button on your remote car starter. Within five seconds of turning it on, turn your key back to the “off” position (or press the start button again).
Why is my remote start suddenly not working?
Check all of the wiring from the remote control receiver to the car's computer, or the starter. Ensure that all cable connectors were crimped properly. Check the key fob battery voltage with a volt meter to insure the battery (or batteries) are dying before you run off to the store in search of new batteries.
How do I reboot my remote?
Before trying any troubleshooting, we recommend you try resetting the remote control:
- Remove the batteries from the remote control.
- On the remote control, press the Power button for three seconds.
- Reinsert the batteries, making sure they are inserted with the correct polarity (-/+), then see if the issue is resolved.
How do I make my Chevy remote start work?
How to Use Chevy Remote Start with Your Key Fob: Press the lock button on your key fob to secure the vehicle. Immediately after pressing the lock, press and hold the remote start button for at least four seconds. If successful, your vehicle's lights will flash and the engine willistart to run.
How do I reset my Chevy remote?
On your Chevy key fob, press and hold the “Unlock” and “Lock” buttons at the same time. Do this until you hear the door locks engage and disengage again. This is an indicator that the key fob has been programmed successfully. Re-insert the newly programmed key into the ignition in the “On” position.
Why is my auto start stop not working?
If your car auto start stop not working, it could be due to a weak battery, faulty sensors, temperature issues, HVAC demands, or outdated software requiring inspection and maintenance. In recent years, car manufacturers have integrated innovative features to improve vehicle efficiency and environmental impact.
How can I get my remote start to work?
Does LOCK/UNLOCK work?
- Check/replace remote batteries. If your remote has USB port, plug it into a USB charger and then try again later.
- Check the remote antenna inside of your vehicle. Make sure that the connecting harness is fully secured.
- Try reprogramming your remotes.
How do you unlock a Chevy remote start?
Remote lock/unlock
- From the My Vehicle tab on the app's Home screen, press and hold the LOCK or UNLOCK icon.
- Keep holding the icon until the words “Keep Holding” are no longer displayed.
- In addition to remote start and lock/unlock, your vehicle may also support additional remote commands from the mobile app.
Why did my remote stop working out of nowhere?
There are many reasons that make your remote not work. However, the most common reasons for a TV remote that is not working are battery issues, paring issues, or infrared sensor issues. Press the power button while pointing the remote control at your TV. Make sure the LED indicator on the TV blinks.
