How do you reset Ford power folding mirrors?
Power folding mirrors on Ford vehicles are reset by a simple re-learn sequence using the mirror switch. In most newer models, folding the mirrors in to the fully folded position and then unfolding them back to their normal position retrains the system.
The exact steps can vary by model and year, and some trims or configurations require additional steps or dealer tools if the mirrors still misbehave after a basic reset. The guide below outlines a common approach and notes potential variations.
Common reset procedure across most Ford models
The following steps cover the typical re-learn sequence used on many Ford vehicles with power folding mirrors.
- Turn the ignition to the On position (with the engine off) or to the Run/Accessory position as recommended by your manual. Do not start the engine.
- Fold both mirrors in using the power-fold switch until they are fully folded, then hold the switch for 2–3 seconds after the mirrors finish moving to help the system register the end position.
- Unfold the mirrors back to their normal driving position using the same switch, ensuring both mirrors reach their usual alignment.
- Test the fold/unfold function several times to confirm the memory position has been relearned. If your model supports auto-fold memory, you should see smooth operation without binding or misalignment.
Repeatedly performing this sequence often reinitializes the mirror control unit and reestablishes the correct fold position and alignment.
Troubleshooting steps if the basic reset doesn’t work
If the basic reset doesn’t fix the problem, try these additional checks and steps to isolate the issue.
- Inspect the fuse for the power-fold mirrors and the fold function in your vehicle’s fuse box, replacing any blown fuse as required.
- Power-cycle the electrical system if you’re comfortable doing so: turn off the ignition, disconnect the battery for a few minutes (observe proper safety procedures and be aware of any vehicle radios or security codes that may require re-entry), reconnect, and then repeat the reset sequence. Note that this can affect other electronic systems.
- If the mirrors still do not fold/unfold correctly or continue to misalign, the issue could be a faulty mirror motor, wiring harness, or control module. In such cases, seek a dealer or qualified automotive technician for diagnostics and potential replacement or reprogramming.
These troubleshooting steps address common non-mechanical issues and simple faults that can affect mirror recall. A persistent problem after these steps often indicates a hardware fault or a need for professional calibration.
Model-specific notes and tips
Ford F-Series trucks and larger SUVs with power-fold mirrors
For many F-Series trucks and larger Ford SUVs, the reset method described above works as a general re-learn. Some trims with additional memory features may require ensuring the door lock is used properly and confirming the mirrors move freely without obstruction before initiating the reset. If the mirrors still fail to save a memory position after the reset, a technician may need to check the mirror motors and related wiring.
Vehicles with auto-dimming or enhanced mirror options
Some models include auto-dimming or additional mirror features that share a common control module. In these cases, you may need to reinitialize related functions (such as dimming or memory) after a reset if you notice mismatched brightness or position. Always verify the reset steps against your specific model year in the owner’s manual, as Ford periodically updates procedures via technical service bulletins.
When to seek professional help
If your Ford power folding mirrors still won’t fold or unfold correctly after the standard reset and basic troubleshooting, book a service appointment. A dealer can diagnose potential motor faults, wiring harness issues, or control module problems and perform programming or replacement as needed.
Summary
Resetting Ford power folding mirrors centers on a simple re-learn sequence: fold the mirrors in, hold briefly, then unfold them out, and test the function. If problems persist, check fuses, consider a controlled power-cycle, and consult a dealer for deeper diagnostics. Model year and trim variations can affect the exact steps, so when in doubt, consult your owner’s manual or a qualified technician for guidance.
What causes side mirrors not to fold?
Non-functional side mirrors occur for various reasons, including blown fuses, faulty mirror switches, or malfunctioning mirror motors.
How to reset folding wing mirrors?
Forward then While pressing the power mirror Switch manually Guide them all the Way Back inward to the folded. Position They should then be res synchronized. And Ready to. Use .
How to program Ford mirrors to fold?
Go down to mirrors. And check off autofold. What we're going to shut the truck. Off we're going to go. Outside. I'm going to grab my key fob hit that lock button.
Why have my electric mirrors stopped working?
If the mirrors are completely unresponsive, a blown fuse could be to blame. Locate the fuse box using your owner's manual, find the correct fuse, and inspect it for damage. If the fuse is damaged, swap it out with a new one of the same amperage. Once replaced, check if the mirrors function properly.
