How do you reset the tire pressure light on a Lexus LX570?

The quickest way to reset the tire pressure warning on a Lexus LX570 is to inflate all tires to the recommended pressures and then use the TPMS reset procedure if your model has a reset switch, or drive at highway speed to trigger a relearn. The exact method can vary by year and trim, so below are the common approaches and what to check if the light stays on.

Manual reset procedure (with TPMS reset button)

This method applies to LX570 models that include a dedicated TPMS reset button. If your vehicle doesn’t have a reset switch, skip to the automatic relearn section.

1. Check all tire pressures when the tires are cold and inflate to the pressures listed on the door jamb placard (or consult the owner's manual).


2. Turn the ignition to ON with the engine OFF (or as instructed in your manual) and locate the TPMS reset button, typically found under the left side of the dashboard near the steering column or under the dash panel.


3. Press and hold the TPMS button until the tire pressure warning light in the instrument cluster blinks or a confirmation is shown (this may take a few seconds).


4. Release the button and start the engine. Drive at a steady speed above about 50 mph (80 km/h) for 10–20 minutes to complete the relearn process.


5. When the light goes off, the system has relearned. If the light remains on, repeat the procedure or proceed to the diagnostic steps below.

After performing the reset, a highway drive helps the system re-calibrate. If the warning light persists, there may be a sensor issue, a slow leak, or a damaged TPMS sensor that requires professional inspection.

Automatic relearn procedure (no reset button or as a supplement)

If your LX570 doesn’t have a TPMS reset button, or you prefer a relearn by driving, use this approach. It relies on correcting tire pressures and then allowing the system to re-synchronize automatically.

1. Inflate all tires to the manufacturer’s recommended pressures as shown on the door jamb placard or in the owner’s manual. Ensure the spare tire is not required for TPMS monitoring in your model year.


2. With the ignition on (engine off) or as specified in your manual, start the vehicle and begin driving on a clear highway. Maintain steady speeds and avoid hard braking or rapid acceleration.


3. Drive at speeds above approximately 50 mph (80 km/h) for at least 10–15 minutes to allow the TPMS to relearn the new sensor configurations and tire pressures.


4. Once you’ve completed the highway drive, check the instrument cluster. If the TPMS light goes off, the relearn was successful. If it remains illuminated, proceed with a diagnostic check or visit a tire shop or dealership.

Note that some conditions, such as a recently replaced tire or sensor, can extend the relearn period. If you recently rotated tires or adjusted wheel components, a longer or repeated relearn drive may be required.

What to do if the light won’t reset

If the TPMS light stays on after trying both methods, you may be dealing with one of several issues: a faulty or dead TPMS sensor, a damaged valve stem, a slow tire leak, or a sensor battery nearing end of life. A professional TPMS diagnostic with a scan tool can identify which sensor (one of the wheels or the spare, if applicable) is failing and whether sensor replacement or programming is needed.

Model-year differences and quick tips

TPMS procedures can vary slightly by LX570 year range and trim. Always consult the owner’s manual for the exact location of the TPMS reset switch (if equipped) and the recommended relearn procedure for your specific year. If the vehicle was recently serviced with new tires or sensors, the reset might require a dealership tool or software reprogramming.

Summary

To reset the tire pressure light on a Lexus LX570, start by ensuring all tires are inflated to the door-jamb specifications. Use the TPMS reset button if your model has one, following the on-screen or indicator prompts, and then drive on highways to complete the relearn. If no reset button is present, inflate to the correct pressures and drive at steady highway speed to allow the system to recalibrate. If the light remains after these steps, seek professional diagnostics to check for sensor faults or leaks.

How do you reset the tire pressure sensor on a Lexus lx570?

To reset the Lexus LX 570's tire pressure, first ensure all tires are properly inflated. Then, either use the TPMS reset button located under the driver's side dashboard near the hood release or use the multi-information display on the steering wheel to navigate to the "TPMS" settings. For the button method, press and hold the button until the indicator light on the dashboard flashes three times, then turn the vehicle off and on again. For the display method, use the steering wheel controls to select "Settings," navigate to "TPMS," and press and hold the center button to start the recalibration. After either method, drive for 10-20 minutes to allow the system to recalibrate.
 
This video demonstrates how to reset the TPMS using the display audio system: 56sLexus DriversYouTube · Apr 1, 2015
Method 1: Using the TPMS reset button 

1. Ensure all tires are inflated to the correct pressure. 
2. Turn the ignition to the "ON" position without starting the engine. 
3. Locate the TPMS reset button, which is often a small button with a tire icon, to the left of the steering wheel or under the driver's side dashboard near the hood release. 
4. Press and hold the reset button until the tire pressure warning light on the instrument panel flashes three times. 
5. Release the button. 
6. Turn the vehicle off, then start it again. 
7. Drive for about 10 to 20 minutes at a speed between 20 and 35 mph to complete the reset. 

Method 2: Using the multi-information display

1. Ensure all tires are inflated to the correct pressure. 
2. Turn the ignition to the "ON" position. 
3. Using the steering wheel controls, navigate to "Settings" or the gear icon. 
4. Scroll to "Vehicle" or "TPMS" and select it. 
5. Select the "TPMS Calibration" or "Set Current Air Pressure" option. 
6. Press and hold the center button to start the calibration process. The system will indicate when it's complete, often with a flashing light. 
7. Drive for 10 to 20 minutes to allow the system to fully recalibrate. 

If the light remains on
If the warning light comes back on after these steps, there may be a different issue with the system, such as a faulty sensor or a low battery in a sensor. In this case, it is best to have the system diagnosed by a professional, such as a Lexus dealership.

How do you reset the low tire pressure light on a Lexus?

Step one adjust the cold tire pressure in all four tires recommended on the tire. Plaqueard. Step two turn the ignition key to the on position without starting the engine.

How do you reset the TPMS on a 2008 Lexus lx570?

Turn the vehicle's ignition to “on” without starting the engine; hold the TPMS reset button until the light flashes three times and release the button. Start the car and give it about 20 minutes—the warning light should disappear.

Where is my TPMS reset button?

Your TPMS reset button is likely located under the steering wheel on the driver's side, but it can also be on the center console, in the glove box, or accessed through the vehicle's display menu. The exact location varies by make and model, so you should consult your car's owner's manual for specific instructions.
 
How to find the button

• Look for a physical button: Check the area under the steering wheel, often to the left of the steering column. 
• Explore the center console or glove box: The button may be on the dashboard near the center console or inside the glove box. 
• Check the dashboard menu: On newer cars, the reset is often done through the vehicle's information display or touchscreen. You may need to press a "Menu," "Settings," or "Vehicle" button to find "TPMS Calibration" or a similar option. 
• Consult your owner's manual: This is the most reliable way to find the button or understand the reset procedure for your specific vehicle. 

After you find the button

• With the ignition on (but the engine off), press and hold the button until the TPMS light flashes three times. 
• Start the car: and wait about 20 minutes for the sensor to reset itself.