How do you reset the TPMS on a Ford Expedition?

Inflate all tires to the recommended cold pressures and then either drive to relearn or perform a manual reset in the vehicle’s settings; the exact steps depend on the model year and trim.

Understanding TPMS and Why Reset Is Needed

The tire pressure monitoring system (TPMS) watches each tire’s pressure and alerts you if a tire is under‑inflated. After inflating tires, rotating them, or replacing sensors, the system may need to relearn which sensor belongs to which wheel. Resetting helps ensure accurate warnings and proper fuel efficiency, but the method varies by year and equipment level.

Automatic Relearn by Driving

For many newer Expeditions, the simplest path is an automatic relearn triggered by regular driving after tires are properly inflated.

When to try automatic relearn

This method works best once all tires are at the correct pressures and you’ve driven on a highway or open road for a while. The vehicle’s TPMS will attempt to relearn sensor positions as you drive.

• Inflate all tires to the recommended cold pressures shown on the door placard, including any spare tire that the system recognizes for your model year.


• Drive at a steady speed, ideally around 50 mph (80 km/h) or higher, for about 10 minutes to allow the sensors to relearn their positions and pressures.


• Observe the TPMS warning light: it should turn off once the relearn is complete. If it stays on, double‑check pressures and consider repeating the drive cycle.

Most modern Expeditions complete the relearn during a routine highway drive, without requiring additional steps.

Manual Reset via Settings or a Physical Button

Some model years support a manual TPMS reset through the instrument cluster menu, an infotainment screen, or a dedicated reset button. If your Expedition supports this, follow these steps. If not, rely on the automatic relearn method above or check the owner’s manual for your exact year and trim.

Model-year variations

Ford periodically updates TPMS procedures across generations. If you don’t see a Reset option in Settings, your vehicle may rely on the drive‑to‑relearn method or require a dealer tool for a manual reset.

• Step 1: With the engine off, turn the ignition to ON (accessory power) without starting the engine.


• Step 2: On the steering wheel controls or touchscreen, navigate to Settings > Vehicle > TPMS or Tire Pressure Monitor, then select Reset or Confirm to begin the relearn process.


• Step 3: Drive as you would for a normal relearn cycle (usually highway speeds for about 10 minutes). The light should go out when the process completes.

Note: In some older or differently equipped trims, there may be a physical TPMS reset button under the dash or near the left kick panel. If you can’t locate a reset option in the menu, consult the owner's manual or a dealer for the exact steps for your vehicle.

What to Do If the Light Remains

If the TPMS light stays on after a full relearn attempt or after confirming proper tire pressures, inspect tires for leaks or damaged sensors. A faulty sensor or a compromised wheel could require professional diagnosis and replacement of the affected sensor.

Summary

Resetting TPMS on a Ford Expedition usually involves inflating all tires to the recommended pressures and either allowing an automatic relearn through a normal highway drive or using a manual reset method via the instrument cluster or settings. Since steps can vary by model year and trim, always consult your owner’s manual for the exact procedure and consider professional help if warnings persist.

How do I manually reset my Ford TPMS?

To reset your Ford's TPMS, first ensure all tires are inflated to the correct pressure listed on the driver's side door jamb. Then, enter the reset mode by either using the dashboard button (if equipped) or by a sequence of ignition and brake pedal presses. Finally, activate each tire's sensor one by one, starting with the front-left, by decreasing the air pressure until the horn honks. 
Method 1: Using a TPMS button on the dashboard
This video demonstrates how to reset the TPMS using the dashboard button on a Ford: 1mHondaYouTube · May 15, 2019

1. Inflate all tires to the correct pressure. 
2. Turn the ignition to the "On" position (engine off). 
3. Press and hold the TPMS button, usually located on the steering column or left of the steering wheel, until the TPMS indicator light flashes twice. 
4. Drive for at least 20 minutes at speeds between 30 and 60 mph for the calibration to complete. 

Method 2: Using the key cycle and brake pedal
This method works for many models, including those with push-button start. 
This video shows how to enter the TPMS training mode using the key and brake pedal sequence on a Ford: 53sShaners Mechanic LifeYouTube · Mar 19, 2023

1. Inflate all tires to the correct pressure. 
2. Press the brake pedal and hold it. 
3. Turn the ignition from Off to Run, three times in a row, ending in the "Run" position. 
4. Release the brake pedal. 
5. The horn will sound once, and the "Train Left Front Tire" message will appear on the display. If not, repeat these steps. 
6. Use a tire pressure gauge to release air from the left-front tire's valve stem until the horn chirps once. 
7. Repeat this process for the right-front, right-rear, and left-rear tires, in that order. 
8. The process is complete when you hear the horn for the last tire. If the horn beeps twice at any point, the procedure failed, and you need to start over. 

Method 3: Using hazard lights (for some models) 
This video shows how to reset the TPMS by flashing the hazard lights on a Ford Transit van: 56sThe OCD RepairmanYouTube · Nov 20, 2023

1. Inflate tires to the correct pressure. 
2. With the ignition on and engine running, turn the hazard lights on and off three times within a 10-second window. 
3. The horn will chirp once to indicate you have entered training mode. 
4. Follow the on-screen prompts to train each tire by deflating the air until the horn honks, starting with the left-front tire. 

Can you reset a Ford TPMS without a tool?

To perform a Ford TPMS relearn without a tool, turn the ignition to the "on" position, then press the hazard light switch 3-6 times within 10 seconds until the horn beeps, indicating you are in training mode. Next, release air from the left front tire until the horn honks once, then move to the right front, right rear, and left rear tires, repeating the process for each one.
 
Step 1: Prepare the vehicle

• Ensure all tires are inflated to at least the pressure recommended on the driver's doorjamb sticker, or lower if you are a tire technician who intends to inflate them after the relearn process. 
• Start the engine and drive for a few minutes at a speed over 20 mph. 
• Turn the ignition to the "on" position without starting the engine. 
• Press and release the brake pedal once. 

This video shows how to prepare the vehicle for the TPMS relearn procedure: 43sReviews and How To's!YouTube · Jan 12, 2018
Step 2: Enter TPMS training mode 

• Press the hazard light button 3 times (or 6 times for some models) within 10 seconds. 
• The horn will beep once, and the instrument cluster will display a message like "Train Left Front Tire". 
• If the horn does not beep, repeat the process. 

Step 3: Train the sensors

• Go to the left front tire. 
• Deflate the tire until the horn honks once. This indicates the system has learned that sensor. 
• Proceed to the other tires in a clockwise pattern: right front, right rear, and left rear. 
• Release air from each tire until the horn honks once for that specific tire. 
• If the horn honks twice, there may be an issue with the sensor or its position. 

You can watch this video to see how to train the TPMS sensors: 59sGregg FestoYouTube · Sep 12, 2022
Step 4: Complete the relearn 

• Once all four tires are trained, the instrument cluster will display a message that the training is complete. 
• You can then inflate the tires to the correct pressure and start the engine. 
• The TPMS light should be off once the vehicle is started and the tires are at the proper pressure. 

Where is the TPMS reset button?

The TPMS reset button is typically located under the steering wheel, on the dashboard, or inside the glove box. If your car has a touchscreen display, the reset function is often found in the "vehicle settings" or "TPMS calibration" menu. For specific locations, check your owner's manual or look for a button with the TPMS icon (a tire with an exclamation mark). 
You can watch this video to learn how to reset the low-tire-pressure indicator on a display audio model: 1mHondaYouTube · May 15, 2019
Common locations

• Under the steering wheel: Look for a button on the left side of the steering column. 
• Glove box: Some vehicles have a hidden button located inside the glove box. 
• Dashboard: The button might be on the side of the dashboard or integrated into the instrument panel. 
• Touchscreen display: Many modern vehicles have the option in the main menu, often under "Vehicle Settings" or a dedicated "TPMS" menu. 

How to reset

1. Adjust tire pressure: Ensure all tires are inflated to the correct pressure, which is usually listed on a sticker in the driver's side door jamb. 
2. Find the reset button: Locate the physical button or navigate to the TPMS menu on the dashboard's infotainment screen. 
3. Press and hold: Press and hold the reset button until the TPMS light flashes three times, or follow the on-screen instructions to select "calibrate". 
4. Drive the vehicle: Drive for at least 5-10 minutes to allow the system to reset. 

This video demonstrates how to reset the TPMS on a Chevy Equinox: 59sPro Tips PlusYouTube · May 4, 2024

Where is the TPMS reset button on a Ford Expedition?

Generally, you'll find the reset button under the steering wheel. If you can't quickly locate it, check your owner's manual.