How do you reset the TPMS sensor on a Ford Transit?

In most Ford Transit models, the Tire Pressure Monitoring System (TPMS) relearns automatically once the tires are inflated to the recommended pressures and you drive the vehicle for several minutes on the highway. If the warning light persists, you can trigger a manual relearn using the vehicle’s settings or a diagnostic tool.

Understanding TPMS Relearn Basics

The TPMS monitors tire pressure in each wheel and learns sensor IDs as part of normal driving. A reset or relearn is often needed after tire service, sensor replacement, or rotating tires. The exact method can vary by model year and infotainment system, so consult your owner’s manual for year-specific instructions.

Automatic relearn: drive and verify

Try the automatic relearn first. These steps reflect common Ford Transit behavior and are designed to be performed without special tools.

1. Inflate all tires to the recommended cold pressures listed on the door placard or in the owner’s manual. Ensure the pressures are checked when the tires are cold.


2. Drive on a clear road at steady speeds for about 10 minutes, ideally on highways or interstates, to allow the system to relearn the sensors.


3. Park the vehicle and observe the TPMS indicator. If the system has relearned successfully, the warning light should turn off.

Usually, you’ll see the light go out after a successful relearn. If the light stays on, proceed to manual relearn methods described below.

Manual relearn and tools

If automatic relearn does not occur, you can trigger a manual relearn using the vehicle’s menus or a diagnostic tool. The exact steps can differ by model year and infotainment setup, so adapt as needed.

Vehicle menu relearn

Use the instrument cluster or Ford SYNC/menus to start a relearn. This method is common on many Transit models where a TPMS relearn option exists in the vehicle settings.

1. Turn the ignition to ON with the engine OFF.


2. Navigate to Settings or Vehicle settings, then find TPMS Relearn (the wording may be “TPMS Relearn,” “Tire Pressure Monitoring,” or similar).


3. Select Relearn and confirm. The system may indicate that learning is in progress.


4. Drive for about 10–20 minutes at highway speeds to complete the relearn process.

Note: If your Transit’s menu layout differs, consult the owner’s manual for the exact path to start a TPMS relearn in your year/model and infotainment system.

Using an OBD-II tool or TPMS relearn tool

Some drivers use a dedicated TPMS relearn tool or an OBD-II diagnostic tool capable of initiating TPMS learning. This approach is helpful if the vehicle’s internal menus do not offer a relearn option or if sensors are not being recognized.

1. Connect a Ford-compatible TPMS relearn tool or an OBD-II tool to the vehicle’s OBD-II port (usually under the left side of the dashboard).


2. Follow the tool’s on-screen prompts to initiate TPMS learning for all sensors. The tool may display success messages when each sensor is learned.


3. Drive as directed by the tool to finalize the relearn, typically at highway speeds for several minutes.

Manual relearn via a tool can be especially helpful after sensor changes or if the vehicle cannot complete a relearn through the onboard system.

When to seek professional help

• The TPMS light remains on after attempting automatic and manual relearn methods.


• You recently replaced tires or sensors and the system cannot learn new IDs.


• You notice inconsistent readings or sensor faults (e.g., a single tire continuously showing low pressure).


• There are signs of damaged sensors or a suspected TPMS circuit fault.

In these cases, a Ford dealer or qualified tire shop can diagnose sensor IDs, replace faulty sensors, or recalibrate the TPMS with factory tools.

Summary

Resetting the TPMS on a Ford Transit usually happens automatically after inflating tires to the recommended pressures and driving at highway speeds for about 10 minutes. If the warning persists, you can trigger a manual relearn through the vehicle’s settings or with an OBD-II/TPMS tool. Always confirm tire pressures first, and consult your owner’s manual for model-year specifics. If problems remain, professional service may be required to diagnose sensor faults or system wiring.

How do I manually reset my Ford TPMS?

To reset your Ford's TPMS, first ensure all tires are inflated to the correct pressure listed on the driver's side door jamb. Then, enter the reset mode by either using the dashboard button (if equipped) or by a sequence of ignition and brake pedal presses. Finally, activate each tire's sensor one by one, starting with the front-left, by decreasing the air pressure until the horn honks. 
Method 1: Using a TPMS button on the dashboard
This video demonstrates how to reset the TPMS using the dashboard button on a Ford: 1mHondaYouTube · May 15, 2019

1. Inflate all tires to the correct pressure. 
2. Turn the ignition to the "On" position (engine off). 
3. Press and hold the TPMS button, usually located on the steering column or left of the steering wheel, until the TPMS indicator light flashes twice. 
4. Drive for at least 20 minutes at speeds between 30 and 60 mph for the calibration to complete. 

Method 2: Using the key cycle and brake pedal
This method works for many models, including those with push-button start. 
This video shows how to enter the TPMS training mode using the key and brake pedal sequence on a Ford: 53sShaners Mechanic LifeYouTube · Mar 19, 2023

1. Inflate all tires to the correct pressure. 
2. Press the brake pedal and hold it. 
3. Turn the ignition from Off to Run, three times in a row, ending in the "Run" position. 
4. Release the brake pedal. 
5. The horn will sound once, and the "Train Left Front Tire" message will appear on the display. If not, repeat these steps. 
6. Use a tire pressure gauge to release air from the left-front tire's valve stem until the horn chirps once. 
7. Repeat this process for the right-front, right-rear, and left-rear tires, in that order. 
8. The process is complete when you hear the horn for the last tire. If the horn beeps twice at any point, the procedure failed, and you need to start over. 

Method 3: Using hazard lights (for some models) 
This video shows how to reset the TPMS by flashing the hazard lights on a Ford Transit van: 56sThe OCD RepairmanYouTube · Nov 20, 2023

1. Inflate tires to the correct pressure. 
2. With the ignition on and engine running, turn the hazard lights on and off three times within a 10-second window. 
3. The horn will chirp once to indicate you have entered training mode. 
4. Follow the on-screen prompts to train each tire by deflating the air until the horn honks, starting with the left-front tire. 

How to reset warning light on Ford Transit?

Together after about 15 seconds the light will start to flash. The service light is now reset. The next step is particularly important for lighter transients which are fitted with a Powertrain module.

Can I reset my own TPMS sensor?

Yes, you can reset your TPMS yourself, but the process varies by vehicle. First, check that all tires are inflated to the correct pressure, which is listed on the driver's side door jamb. Then, look for a physical reset button, check your car's infotainment system for a "TPMS calibration" option, or perform a specific procedure like disconnecting the battery or overinflating and deflating the tires. After performing the reset, you may need to drive for a short time for the system to fully recalibrate. 
Before you begin

• Check tire pressure: Park on a level surface and use a pressure gauge to check that all four tires (and the spare, if applicable) are at the manufacturer's recommended PSI, found on the sticker on the driver's side door jamb or in your owner's manual. 
• Wait for tires to cool: Ensure your tires are cool for an accurate reading. 

This video shows how to check tire pressure and reset the TPMS system: 47sHondaYouTube · May 15, 2019
DIY reset methods
Method 1: Use a dedicated reset button 

1. Ensure the ignition is turned to the "ON" position without starting the engine. 
2. Locate the TPMS reset button. It is often a small button with a TPMS icon, typically found under the dashboard to the left of the steering wheel, in the glove box, or on the center console. 
3. Press and hold the button until the TPMS warning light blinks three times, then release it. 
4. Start the car and drive for a few minutes. The light should turn off. 

This video demonstrates how to use the TPMS reset button on a vehicle: 1mApple DrainsYouTube · Oct 5, 2012
Method 2: Use the infotainment or dashboard menu 

1. Navigate to the "Settings" menu on your infotainment screen. 
2. Find the "Vehicle" settings and look for a "TPMS calibration" or "Tire pressure" option. 
3. Select "Calibrate" to start the process. 
4. Drive for about 20–30 minutes at speeds between 30–60 mph to allow the system to complete the recalibration. 

Method 3: Try a "re-learn" procedure (some vehicles) 

1. Turn the ignition to "ON" and press the "Info" or "Check" button until the display says "Press CHECK button to relearn tire positions". 
2. Press the "CHECK" button to start the relearn procedure. 
3. The system will signal which tire to start with (e.g., the driver's front tire). 
4. Let air out of that tire for about 5 seconds, or until the horn beeps to confirm the system has registered it. 
5. Repeat this for the other three tires in the correct sequence. 

This video explains how to perform the TPMS relearn procedure, which involves deflating and inflating the tires: 1mlmfscrewYouTube · Jun 28, 2020
If the light remains on

• Check your owner's manual: Your car's manual will have the most accurate instructions for your specific make and model. 
• Consider sensor failure: The TPMS sensors have a lifespan of about 7-10 years. If the light comes on shortly after a reset, one or more of the sensors may have failed and will need to be replaced. 
• Visit a professional: If you cannot get the light to turn off after trying these methods, a professional can use a diagnostic tool to check the system and the sensors. 

How do you reset the tire pressure sensor on a Ford Transit van?

To reset the Ford Transit TPMS, inflate all tires to the correct pressure and then enter training mode by cycling the ignition or hazard lights. The exact method depends on your model: 

• Key ignition models: Turn the key to "RUN" 3 times (engine off) and press the brake pedal. Then turn the ignition OFF, and turn it back to "RUN" 3 times. The horn will beep, and you can then use the reset button or the hazard light switch method to train the sensors, typically by releasing air until the horn beeps again for each wheel. 
• Push-button start models: Cycle the push-button start to the Accessory (ACC) mode 3 times, ending in ACC. Turn the ignition off, then press the brake and cycle the push-button start to ACC again 3 times to initiate training mode. A message will appear, and you can then train the sensors. 
• Display audio models: Navigate to Settings > Vehicle > TPMS Calibration on the touchscreen and press Calibrate. Then, you must drive for about 30 minutes to complete the process. 

This video shows how to reset the TPMS on a Ford Transit using the hazard light method: 56sThe OCD RepairmanYouTube · Nov 20, 2023
Before you begin

• Check the driver's side door jamb or your owner's manual for the correct tire pressure for your vehicle.
• Inflate all tires to the recommended pressure, including the spare. 

For models with a key ignition

1. Turn the ignition to the OFF position. 
2. Press and release the brake pedal. 
3. Turn the ignition from OFF to RUN three times within 10 seconds, ending in the RUN position. Do not start the engine. 
4. The horn will beep once to signal that the TPMS relearn mode has been activated. 
5. You will see a message like "TRAIN LEFT FRONT TIRE" on the display. 
6. To train each sensor:
   • Release some air from the left front tire until you hear a horn beep. 
   • Move to the next tire in sequence (right front, right rear, left rear, spare) and repeat the process until the horn beeps again. 
7. After the spare tire is trained, the message will change to "TRAINING COMPLETE," and the light should turn off. 

For models with a push-button start

1. Press the start button once without your foot on the brake, so the vehicle is in ACC mode. 
2. Power off the vehicle by pressing the button once. You will need to do this two more times, ending in ACC mode. 
3. Press and release the brake pedal, then turn the ignition completely off. 
4. Turn the ignition to ACC again, and then power off one more time. Repeat this two more times, ending in ACC mode. 
5. The horn will sound once, and the TPMS telltale will blink once, initiating the training mode. 
6. Follow the on-screen prompts to train each tire by releasing air from the valve stem until the horn beeps. 
7. After the last tire is trained, you will see a "TRAINING COMPLETE" message. 

For models with a display audio system

1. Make sure the vehicle is on and parked with the parking brake set.
2. Press the Home button on the display screen.
3. Touch Settings.
4. Touch Vehicle.
5. Select TPMS Calibration.
6. Touch Calibrate.
7. The calibration process will begin. You will need to drive the vehicle for about 30 minutes at speeds between 30 and 60 mph for it to complete. 

If the light stays on after a reset

• The reset may have failed, which could be due to an inaccurate sensor. 
• You may need to replace the sensor battery if the light is flashing instead of solid. 
• Contact a professional at a service center for further diagnosis.