How many quarts of oil does a 2004 Cavalier 2.2 take?
Approximately 4.5 quarts of engine oil are required for a standard oil change on a 2004 Cavalier with the 2.2-liter engine when the filter is replaced. If you do not replace the filter, the capacity is around 4.0 quarts.
The 2004 Cavalier 2.2L uses a 4-cylinder engine shared across GM's compact lineup. Oil capacity can vary slightly by the exact engine variant and service method. This article outlines the standard figures and practical guidance to help you plan a compliant oil change.
Oil capacity specifics for the 2.2L Cavalier
The figures below assume a normal oil change with the oil filter replaced. Use them as a guideline and always verify with the dipstick and owner's manual.
With the oil filter installed
Before listing the capacity, note that this figure includes the oil needed to fill the new filter during a standard change.
- Approximately 4.5 quarts
These figures account for pan oil plus the oil needed to fill a new filter during service.
Without replacing the oil filter
If the service does not involve replacing the filter, the engine oil capacity is about 4.0 quarts.
- Approximately 4.0 quarts
Always verify the final level with the dipstick after adding oil, especially when changes involve unusual drain conditions or nonstandard filter choices.
Recommendations on oil type and maintenance tips
For a 2004 Cavalier 2.2, GM manuals typically specify SAE 5W-30 as a common viscosity across a wide temperature range. Depending on climate or dealer guidance, 5W-20 may also be acceptable. Always consult the owner's manual or a GM service professional for the exact specification for your engine code and location.
Summary: The vehicle typically takes about 4.5 quarts of oil with a new filter; about 4.0 quarts if the filter is not replaced. Verify with the dipstick after filling and follow the factory specifications for oil grade and change intervals.
In short: plan for roughly 4.5 quarts (with filter) and 4.0 quarts (without filter), then confirm the level with the dipstick and consult the manual for the precise oil type and service schedule.
How much oil does a 2004 Chevy Cavalier 2.2 take?
The 2004 Chevy Cavalier 2.2L engine requires approximately 5.1 quarts of oil with a filter change when using a viscosity like 5W-30. Always check the dipstick after refilling to ensure the correct level is reached, as some sources may indicate slightly different capacities around 4.5 to 5 quarts.
- Oil capacity: 5.1 quarts with a new filter.
- Recommended viscosity: 5W-30 is preferred for all temperatures, but 10W-30 can be used if temperatures are consistently above -18°Cnegative 18 degrees cap C−18°𝐶.
- Important: After changing the oil, run the engine briefly, then check the dipstick to confirm the oil is at the proper level. This accounts for any minor variations.
How much oil does a 2.2 Cobalt take?
The 2.2L Chevy Cobalt has an oil capacity of approximately 5 quarts when changing with a filter, although some sources list slightly different amounts for specific model years (e.g., 4.7 to 5.1 quarts). Always check the dipstick after adding the new oil to ensure the level is correct.
- Capacity: Approximately 5 quarts with a new filter.
- Oil Viscosity: 5W-30 is the recommended grade for most conditions.
- Important: After refilling, run the engine briefly, shut it off, wait a minute, and then check the oil level with the dipstick and add more if needed to reach the full mark.
How many quarts of oil does a 2.2 engine hold?
About 5 1/2 to 6 quarts for engine oil. About 8 gallons of mineral oil or hytran if you have a loader or external hydraulics. Engine holds 6 qt with the filter 5 without. Rear end holds 8 gallons.
How many quarts does a 2.2 Chevy Cavalier take?
Capacity: 4.5 quarts (with filter). After refill check oil level.
