How many quarts of oil does a 2018 Lexus NX 300 2.0 Turbo take?
The 2018 Lexus NX 300 with the 2.0-liter turbo engine takes about 5.4 quarts of engine oil when you replace the oil filter; without changing the filter, you’ll typically need around 4.7 quarts. The recommended oil is synthetic 0W-20. These figures are drawn from the official service specifications for the NX 200t/ NX 300 models and are widely used by technicians and owners as a standard reference.
Oil capacity at a glance
Understanding the official capacities helps owners plan proper oil-change procedures and future top-offs. The key numbers below reflect the typical service standard for the 2018 NX 300 2.0 Turbo.
- Oil capacity with filter: 5.4 quarts (approximately 5.1 liters)
- Oil capacity without filter (draining only): about 4.7 quarts (approximately 4.4 liters)
- Recommended oil grade: SAE 0W-20 synthetic
- Oil type notes: Use a Lexus-approved full synthetic oil that meets ILSAC GF-6 (or API SN) specifications; verify local requirements in the owner’s manual
In practice, always confirm the exact specification for your market in the owner’s manual or with a Lexus dealer, as regional variants can differ slightly.
Oil-change specifics and best practices
When performing an oil change, following the correct capacity and using the right grade ensures optimal engine protection and performance. The NX 300 2.0 Turbo is designed to run on a full-synthetic 0W-20 oil, and the total capacity includes the oil filter in most service scenarios.
Before the list: The steps below outline common procedures and checks you’ll encounter or perform during an oil change, whether you’re doing it yourself or coordinating with a shop.
- Warm up the engine briefly to circulate oil, then park on level ground and turn off the engine.
- Raise the vehicle safely and place a drain pan beneath the oil pan drain plug.
- Remove the drain plug and allow the old oil to drain completely; replace the drain plug with a new washer if required and tighten to the manufacturer’s torque specification.
- Remove and replace the oil filter; lubricate the gasket on the new filter with a bit of fresh oil before installing.
- Pour in the recommended amount of 0W-20 oil (start with about 5.0 quarts, then check the dipstick and add as needed to reach the full mark).
- Replace the oil filler cap, start the engine, and run it for a few minutes; recheck for leaks, then turn off and wait a few minutes to recheck the dipstick and confirm the oil level is at the full mark.
Following these steps helps ensure the engine is properly lubricated and the level is correct after a full oil change.
Notes on accuracy and regional variations
Oil capacity can vary slightly by market due to regional specifications, engine revisions, or differing filter sizes. Always consult your local Lexus dealer or the owner’s manual for the exact figure applicable to your vehicle and region.
Summary: For a 2018 Lexus NX 300 2.0 Turbo, plan on about 5.4 quarts of synthetic 0W-20 oil with a new filter; if you drain only and don’t replace the filter, you’ll use roughly 4.7 quarts. Use the recommended oil grade and verify the level with the dipstick after the change to ensure proper operation.
How many quarts of oil does a 2018 Lexus NX 300 take?
The 2018 Lexus NX 300 has an oil capacity of 5.2 quarts (4.9 liters) with a new filter, and it requires 0W-20 synthetic oil. After changing the oil and filter, you should check the level to ensure it's correct.
- Capacity: 5.2 quarts (4.9 liters) with filter
- Recommended Oil: 0W-20 synthetic
What kind of oil does a Lexus nx200t take?
The Lexus NX200t requires 0W-20 full synthetic motor oil, and the capacity is 5.2 quarts with a filter change. While 5W-20 can be used in a pinch, it's crucial to switch back to 0W-20 at the next oil change.
Oil specifications
- Viscosity: 0W-20 (full synthetic)
- Capacity: 5.2 quarts (with filter)
- Alternative: 5W-20 can be used temporarily if 0W-20 is unavailable, but you must switch back at the next oil change.
- Drain plug torque: 30 ft/lbs
Important notes
- Always use a new drain plug washer when replacing the oil.
- Checking the oil level after refilling is recommended.
- 0W-20 is recommended for optimal fuel economy and cold-weather performance.
What oil for 2018 Lexus Nx300?
The 2018 Lexus NX300 requires 0W-20 full synthetic engine oil and takes approximately 4.6 to 5.2 quarts of oil with a filter change. It's recommended to use a full synthetic oil for optimal engine protection and performance.
- Oil type: 0W-20 full synthetic
- Oil capacity: Approximately 4.6 to 5.2 quarts (with filter)
- Certification: Look for oil that meets the required specifications, such as ILSAC GF-6A
- Alternative: If 0W-20 is unavailable, 5W-20 can be used temporarily, but you must switch back to 0W-20 at the next oil change.
How much oil does a 2018 Lexus 2.0 take?
Capacity: 5.2 quarts (with filter).
