How many quarts of oil does a 3.6 Chevy Traverse take?
The 3.6-liter V6 in the Chevrolet Traverse typically requires about 5.7 quarts of engine oil when you change the oil and replace the filter.
Oil capacity can vary slightly by model year or engine variant used in the Traverse. The most common figure is 5.7 quarts (roughly 5.4 liters) with a new filter. Always verify the exact specification in your owner’s manual or by checking GM’s service information for your VIN.
Oil capacity specifics for the 3.6L Traverse
The following detail outlines the standard capacity you should plan for during a typical oil change on a 3.6L Traverse:
- 5.7 quarts (5.4 liters) of engine oil, including the new oil filter, for a standard oil change on most 3.6L V6 Traverse models.
In practice, some years or configurations may show slight variations (roughly 5.0–6.0 quarts). Always top off with the dipstick to reach the proper full level after installing fresh oil and a new filter.
Recommended oil type and maintenance notes
Use Dexos1 Gen 2 rated 5W-30 synthetic or synthetic-blend oil unless your manual specifies an alternative. Following the manufacturer’s guidelines for oil grade and change intervals helps protect the engine and maintain performance; always consult your owner’s manual for the exact requirements and interval recommendations for your vehicle’s year and configuration.
Summary
For most 3.6L Chevrolet Traverse engines, plan on about 5.7 quarts of oil per oil change with the filter included. Use a Dexos1 Gen 2 5W-30 oil (or the grade specified in your manual) and follow the recommended maintenance intervals. If in doubt, confirm the exact capacity for your specific year and VIN in the official GM documentation or your owner's manual, and always verify the level with the dipstick after the change.
How much oil do you put in a 3.6 L V6?
The oil capacity for a 3.6L V6 engine is typically 5 to 6 quarts, but it varies by vehicle model and year. For a 2020 Dodge Charger, it's around 5.9 quarts, while a 2023 Jeep Wrangler requires 5 quarts. Newer Jeeps, such as the 2016-2021 Grand Cherokee and Durango, often require 6 quarts. Always check your specific owner's manual for the most accurate information, as it can differ even within the same engine family.
- 5 quarts: Common in many models like the 2020 Jeep Wrangler and 2025 Ram 1500.
- 5.9 quarts: The capacity for some models, such as the 2020 Dodge Charger.
- 6 quarts: Required for certain vehicles, including the 2013 JK Jeep Wrangler and some 2016-2021 Grand Cherokee and Durango models.
- Check your owner's manual: This is the most reliable source for your specific vehicle's oil capacity.
- After refilling: It's important to check the oil level with the dipstick after refilling to ensure it is correct.
How many quarts of oil does a 2012 Chevy Traverse take?
The 2012 Chevy Traverse has an oil capacity of 6 quarts with a new filter, and uses 5W-30 oil. It's important to check the oil level with the dipstick after refilling, as some models may require slightly less (e.g., 5.5 quarts) to reach the "full" mark.
- Capacity: 6 quarts (with filter)
- Oil Viscosity: 5W-30
- After refill: Check the dipstick to ensure the oil level is correct, as some may take less.
How much oil does a 3.6 liter Chevy take?
6 quarts
3.6L V6 —6 quarts.
What kind of oil does a GM 3.6 V6 take?
SAE 5W-30 full synthetic
If you have the 3.6L V6 engine, use SAE 5W-30 full synthetic engine oil.
