How much coolant does a Dodge Caliber hold?
The Dodge Caliber's cooling system holds roughly 6.5 to 7 quarts (about 6.2 to 6.6 liters) of coolant in a standard, factory-fill configuration. The exact amount varies by engine option and whether you include heater-core lines, so check your owner's manual for the precise figure for your car.
Engine options and overall capacity
The Caliber came with two main engines, each with a slightly different total cooling-system volume. The estimates below reflect common factory-fill capacities for these engines in standard configurations from 2007–2012.
- 2.0 L World I-4: approximately 6.5–6.9 quarts (about 6.2–6.5 liters) of total coolant for a complete system fill, including the radiator, engine block, heads, hoses, and heater core connections.
- 2.4 L World I-4: approximately 6.8–7.0 quarts (about 6.4–6.6 liters) for a complete system fill with standard components.
These ranges cover the typical factory-fill capacity and provide a practical guide for maintenance and topping off. For exact specs, consult the owner's manual or service documentation for your vehicle's VIN.
How to verify and top off safely
To safely maintain the cooling system, follow the steps below for checking and topping off coolant, using the manual-recommended coolant and proper mixtures.
- Check the vehicle manual for the exact coolant specification and capacity for your year and engine code. Use the recommended type (often Dex-Cool HOAT for Chrysler products) and a 50/50 mix with distilled water unless otherwise directed.
- With the engine cold, inspect the expansion tank (or radiator reservoir) to see the MIN and MAX marks, and keep the level between them when cold. Do not open the radiator cap on a hot engine.
- If topping off, pour slowly to avoid air locks and re-check after the engine runs to operating temperature, then re-check again after it cools.
Regular checks help prevent overheating, corrosion, and potential engine damage. If you notice persistent coolant loss or leaks, have a professional inspect the system.
Summary
The Dodge Caliber's cooling system typically holds about 6.5–7.0 quarts (roughly 6.2–6.6 liters) of coolant, with small variations by engine (2.0 L vs 2.4 L). Always verify the exact capacity in your manual, use the recommended coolant type, and follow safe topping procedures to maintain the system's integrity.
How many gallons of coolant do I need?
You will likely need between 1 and 2 gallons of coolant concentrate to mix with an equal amount of distilled water for a 50/50 solution, but the exact amount depends on your vehicle's cooling system capacity, which can range from 3 to 7 liters (or about 0.75 to 1.75 gallons). It is best to consult your owner's manual or purchase a slightly larger quantity, such as two gallons of concentrate, to ensure you have enough, as some systems can hold more and you may need extra to top off.
How to determine the right amount
- Check the owner's manual: This is the most reliable method, as it will state the exact capacity of your vehicle's cooling system. Look for information under "fluid capacities".
- Estimate based on engine size: If you don't have the manual, you can estimate that 4-cylinder engines generally require between 1 and 2 gallons of a 50/50 mix. Larger engines will need more.
- For a complete flush: If you are doing a full coolant flush, you will likely need more concentrated antifreeze. You can start by adding about 4 gallons of concentrate to a system that holds 8 gallons total, as you can't drain all the old coolant, and then fill the rest with distilled water.
- For topping off: If you are just topping off the system, add enough to reach the "COLD" line on the overflow tank. The amount will be much smaller, likely less than a quart, says this Quora post.
Important tips
- Always use distilled water: Never use tap water, as the minerals can cause corrosion in your cooling system.
- Mix it correctly: Make sure to mix the antifreeze with distilled water in a 50/50 ratio for optimal protection.
- Check the level after service: After refilling, run the engine and keep an eye on the coolant level, as air bubbles may need to be "burped" out of the system.
How many gallons does a Dodge Caliber hold?
The Dodge Caliber's gas tank size is approximately 13.6 gallons for most models, though some all-wheel-drive (AWD) versions and specific model years may have a slightly smaller capacity of around 13.5 gallons.
- Standard capacity: The most common fuel tank size for the Dodge Caliber is 13.6 gallons.
- AWD models: Some all-wheel-drive models may have a slightly smaller tank of about 13.5 gallons.
- Model year variations: While 13.6 gallons is the general size, some sources list a 13.5-gallon capacity for specific models and years.
How much coolant does a 2007 Dodge Caliber take?
Engine Speed 6750 rpm (electronically limited) Fuel Requirement 91 RON unleaded petrol Oil Capacity 4.7 L (5.0 qt.) Coolant Capacity 6.8 L (7.2 qt.)
PDF
How many quarts does a Dodge Caliber take?
4.5 quarts (with filter).
