How much coolant does a Dodge Charger 5.7 take?
The Dodge Charger with a 5.7L Hemi generally holds about 12.9 quarts (roughly 12.2 liters) of coolant in its full cooling system. Exact capacity varies by model year and configuration, so consult the owner's manual or a dealership service guide for your VIN-specific figure.
Coolant capacity is determined by the entire cooling circuit, including the engine block, radiator, hoses, heater core, and reservoir. While the typical range sits around the low to mid-teens in quarts, small changes in radiator size, heater core, or auxiliary cooling components can shift the total slightly. This article outlines the general figures and how to verify the precise amount for your car.
What to know about the 5.7L cooling system
The 5.7L Hemi’s cooling system is designed to keep the V8 properly temperature-controlled under a variety of driving conditions. Because production changes across model years and trims can affect the exact volume, owners should treat the quoted figure as a close estimate rather than a universal constant.
Estimates for the full cooling system capacity (engine block, radiator, hoses, and heater core) typically fall within a narrow band. The most commonly cited range for the Charger’s 5.7L configuration is just under to just over 13 quarts, with minor year-to-year variation.
- 2005–2010 Chargers with 5.7L Hemi: approximately 12.9 quarts (12.2 liters)
- 2011–2014 Chargers with 5.7L Hemi: approximately 13.0 quarts (12.3 liters)
- 2015–2023 Chargers with 5.7L Hemi: approximately 12.9–14.5 quarts (12.2–13.7 liters)
Concluding note: use these figures as a guide, but verify the exact capacity for your specific vehicle using the owner's manual, service bulletin, or by checking the vehicle’s VIN-specific data at a dealer. Small differences in heater core size, radiator, or aftermarket cooling components can adjust the total slightly.
How to find the exact capacity for your Charger
To determine the precise coolant capacity for your exact Charger, consider these reliable sources:
- Check the owner's manual for the official cooling system specification for your year and trim.
- Look up the vehicle’s VIN on Mopar service databases or with a dealership service department for a VIN-specific figure.
- Consult the factory service manual or a trusted automotive repair database for the exact coolant capacity and system diagram.
If you are planning a coolant change, use the exact capacity to guide how much coolant to purchase or drain, and always replace with the correct specification and mixture as recommended by Chrysler.
Coolant type and mixing guidelines
Use the coolant type specified by Chrysler for the 5.7L Hemi, typically a HOAT (Hybrid Organic Acid Technology) coolant meeting Chrysler’s specifications. Many owners use a 50/50 premixed coolant or a concentrate that is mixed with distilled water at the factory-recommended ratio. Do not mix incompatible coolant types, and be sure to flush the system if you are switching from one coolant type to another.
- Follow the manufacturer’s specification (Mopar-approved HOAT or an equivalent that meets Chrysler requirements).
- Prefer a 50/50 mix of coolant and distilled water unless your climate or manual specifies a different ratio.
- Properly bleed air from the cooling system after refilling to prevent air pockets and overheating.
Always dispose of old coolant responsibly and never mix used coolant with fresh coolant from a new container. If in doubt, consult a professional technician or your local dealership service department for guidance.
Summary
The Dodge Charger with a 5.7L Hemi typically requires about 12.9 quarts (roughly 12.2 liters) of coolant for the full cooling system, though exact capacity varies by year and configuration. For the safest result, confirm the precise figure in your owner's manual or via the dealer, use the recommended coolant type, and maintain the system with the correct 50/50 mixture as advised. Accurate capacity helps ensure proper maintenance, efficient cooling, and long engine life.
What type of antifreeze does a 5.7 Hemi take?
For a 5.7 Hemi engine, you need Mopar's 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) coolant. This specification is often identified by the Chrysler/FCA standard MS-90032 and is typically a purple or bluish-purple color. Always verify the correct coolant in your vehicle's owner's manual, as it is the most definitive source.
Key coolant specifications
- Type: OAT (Organic Additive Technology)
- Mopar Specification: MS-90032
- Color: Typically purple or bluish-purple
- Product examples: Mopar's 10 Year/150,000 Mile Formula OAT, or a compatible OAT coolant from brands like Prestone that specifically meets the MS-90032 specification
Important considerations
- Check the manual: The owner's manual is the most reliable source for the correct coolant specification for your specific vehicle year.
- Color is not a reliable indicator: Do not rely on color alone to determine the correct coolant, as different manufacturers use different colors for the same or similar specifications.
- Use the right formula: Mixing different types of coolant can damage the system. Ensure you use a coolant that meets the OAT MS-90032 specification, not a universal or HOAT (Hybrid Organic Acid Technology) type like the older G05 which might be recommended for some older Chrysler products, but is not the correct specification for most 5.7 Hemi engines from around 2013 onwards.
How many quarts does a 5.7 Dodge Charger take?
7 quarts
Engine Oil
Capacity: 7 quarts (with filter).
How many gallons are in a 5.7 charger?
The Charger has an 18.5-gallon gas tank capacity which makes the Charger a long-running presence on any road.
How much coolant does a 5.7 Hemi charger hold?
Coolant Capacity 13.9 litres (14.7 qt.)
