How much horsepower does a 1988 Ford Bronco II have?
The 1988 Ford Bronco II, a compact SUV produced by Ford, had a standard engine that generated 140 horsepower. This was the base engine option available for the Bronco II that year.
Engine Specifications for the 1988 Ford Bronco II
The 1988 Ford Bronco II was available with two engine options:
- 2.9L V6 Engine: This was the standard engine, producing 140 horsepower and 170 lb-ft of torque.
- 2.9L Turbocharged V6 Engine: This optional engine produced 155 horsepower and 190 lb-ft of torque.
Both engine options were paired with a standard 5-speed manual transmission or an optional 4-speed automatic transmission.
Comparing the Bronco II to Other SUVs of the Era
In the late 1980s, the Bronco II's 140 horsepower engine was fairly typical for a compact SUV. For comparison:
- The 1988 Jeep Cherokee had a standard 2.5L 4-cylinder engine producing 117 horsepower.
- The 1988 Chevrolet S-10 Blazer had a standard 2.8L V6 engine producing 125 horsepower.
- The 1988 Toyota 4Runner had a standard 2.4L 4-cylinder engine producing 116 horsepower.
So the Bronco II's 140 horsepower V6 engine was on the more powerful end of the compact SUV spectrum in 1988.
Did the Bronco 2 come with a V8?
Two different V8 engines were offered for the second generation Bronco: the 5.8L 351M and the 6.6L 400. While offering virtually the same horsepower output, the 400 produced a higher torque output over the 351M. As the 460 V8 was restricted to rear-wheel drive F-Series trucks, it was not offered in the Bronco.
Are all Bronco II 4x4?
All Bronco IIs were four-wheel drive until 1986 when the rear-wheel-drive layout became standard. Rear-wheel-drive models were still equipped with a transfer case, capped or sealed where the front driveshaft was connected on four-wheel-drive versions.
Can you put a V8 in a Bronco 2?
The original Bronco II and Ranger transmissions are too weak to withstand V8 power and must be swapped for a heavier duty transmission. You have the option of changing your Manual truck to an automatic, or vice versa at this point.
How much horsepower does a 1988 Ford Bronco 2 have?
140-horsepower
control valve to selectively modulate rear brake line hydraulic pressure. The result is enhanced driver ability to con- trol braking performance (see illustration). All Bronco IIs feature the 2.9 liter V-6 engine with its 140-horsepower output.
How much horsepower does a 1988 Ford Bronco have?
FORD Bronco 5.8L V8 4AT AWD (213 HP)
| ENGINE SPECS - 5.8L V8 4AT AWD (213 HP) | |
|---|---|
| Cylinders: | V8 |
| Displacement: | 5766 cm3 |
| Power: | 156.7 KW @ 3800 RPM 213 HP @ 3800 RPM 210 BHP @ 3800 RPM |
| Torque: | 315 lb-ft @ 2800 RPM 427 Nm @ 2800 RPM |
What is a 1988 Ford Bronco worth?
The value of a 1988 Ford Bronco Custom can vary greatly depending on its condition, mileage, options, and history. Typically, you can expect to pay around $14,667 for a 1988 Ford Bronco Custom in good condition with average spec.
What engine is in a 1989 Bronco 2?
FORD BRONCO II ENGINEERING
The 2.9L multi-port electroni- cally ruel-injected V-6 delivers 140horsepower at 4600 rpm.
How much horsepower does a 1986 Ford Bronco 2 have?
For 1986, the Bronco II's 2.8L V6 was replaced with a 2.9L V6. The displacements were similar, the engine configuration was the same, but the horsepower saw a major boost. With no other changes, the Bronco II went from 115 horsepower to 140.
What is the rarest Bronco?
Ford Bronco U13 Roadster
What is the rarest Bronco? The Ford Bronco U13 Roadster is the rarest Bronco, with only 212 sold in total in its 1968 model year.
What transmission is in a 1988 Ford Bronco 2?
| Ford Bronco II | |
|---|---|
| Transmission | Manual: 4-speed Mazda TK4 5-speed Mazda TK5 5-speed Mazda M5OD-R1 5-speed Mitsubishi FM145 5-speed Mitsubishi FM146 Automatic: 3-speed C5 4-speed A4LD |
| Dimensions | |
| Wheelbase | 94.0 in (2,388 mm) |
| Length | 1983–1988: 158.3 in (4,021 mm) 1989–1990: 161.9 in (4,112 mm) |
