How much oil does a 2010 Honda Element take?
The 2010 Honda Element uses a 2.4-liter four-cylinder engine that requires about 4.5 quarts (4.3 liters) of engine oil with a new filter. If you are not replacing the filter, you’ll need about 4.0 quarts. The recommended oil grade is 5W-20, either conventional or synthetic, and you should follow Honda’s maintenance minder for service intervals.
Engine oil capacity and specifications
Key figures and oil recommendations for keeping the Element’s engine properly lubricated.
- Engine oil capacity with filter: 4.5 quarts (4.3 liters)
- Engine oil capacity without filter: 4.0 quarts (3.8 liters)
- Recommended oil grade: 5W-20, API SN or newer (conventional or synthetic)
- Notes: If you use synthetic oil, ensure it meets Honda’s specifications and change intervals.
In practice, this means planning for roughly 4.5 quarts of oil during a standard change with a new filter, and topping up after initial filling if needed.
Oil grade and change interval notes
For the 2010 Element, Honda specifies 5W-20 oil. You can use conventional or synthetic oil as long as it meets Honda’s specifications and API certification. The recommended oil-change interval depends on driving conditions and the vehicle’s maintenance minder, but typical schedules align with the owner’s manual guidance or maintenance minder prompts.
Do-it-yourself oil change steps
When performing the change yourself, follow these steps to ensure a clean drain, proper fill, and safe disposal.
Here is a typical sequence for a standard oil change on the Element.
- Prepare: Park on level ground, engage the parking brake, and gather tools and the required oil amount (about 4.5 quarts with a new filter).
- Warm up the engine to operating temperature, then turn it off and let it sit briefly.
- Position a drain pan under the oil pan and remove the drain plug; allow the oil to drain completely.
- Replace the drain plug with a new washer if needed and tighten to the specified torque.
- Remove the old oil filter and let any residual oil drain out.
- Install the new oil filter, lightly oil the gasket, and hand-tighten fully.
- Pour in approximately 4.5 quarts of 5W-20 oil (start with 4.5 qt and check the level).
- Run the engine for a few minutes, then turn it off and check the oil level with the dipstick; add oil in small increments to reach the full mark.
- Check for leaks around the drain plug and filter; wipe any spills and ensure the area is clean.
- Dispose of used oil and the old filter at a recycling center or auto shop per local regulations.
After the first drive cycle, recheck the oil level and top off if necessary. Do not overfill the engine, as that can cause performance issues.
Best practices for DIY oil changes
Use a clean funnel to avoid spills, keep the workspace well-ventilated, and double-check that the drain plug and filter are secure. Always recycle used oil and filters in accordance with local regulations, and reset the maintenance minder if your vehicle supports it.
Summary
The 2010 Honda Element typically requires about 4.5 quarts (4.3 liters) of engine oil with a new filter, or about 4.0 quarts (3.8 liters) if the filter is not replaced. Use 5W-20 oil that meets Honda specifications, and follow the owner’s manual or maintenance minder for replacement intervals. Always dispose of used oil responsibly and verify the level with the dipstick after filling.
How much oil does a 2.4 L Honda Element take?
4.4 quarts
Capacity: 4.4 quarts (with filter).
How many quarts of oil does a 1.8 L engine take?
And this 1.8 L takes about four quarts. So we got a 5Q jug here we're going to just pour out about four quarts Probably helpful to have a funnel too i will link one down. Below.
How many quarts of oil does a 2010 Honda Element take?
And start our oil pour this vehicle is going to call for 4 and 12 quarts that's including whatever you put into your oil filter. And that's four and a half quarts. So we're going to remove our funnel.
How many quarts are in a Honda Element?
4.4qt gets me close to the top line. In my Element and CRV.
