How much oil does a 2019 Lexus RX 350 take?
The 2019 Lexus RX 350 typically requires about 6.4 quarts of synthetic engine oil when you change the oil and filter, using 0W-20 oil. This article breaks down the capacity, recommended oil, and practical steps for a DIY oil change or a visit to the shop.
Oil capacity and specifications
The RX 350 is powered by a 3.5-liter V6, and Lexus specifies an oil capacity of 6.4 quarts (6.1 liters) with the oil filter change. The recommended viscosity for most operating conditions is 0W-20 synthetic oil. Always verify the exact specification for your vehicle in the owner’s manual or the under-hood label, since climate and market variations can influence the recommended grade.
What you’ll need for an oil change
Gathering the right supplies before you begin helps ensure a smooth, clean change and reduces the chance of over- or under-filling.
- 0W-20 synthetic motor oil (approximately 6.4 quarts, including the filter)
- Replacement oil filter designed for the 2019 RX 350
- New drain plug washer (if your plug uses one)
- Oil filter wrench
- Oil drain pan and a funnel
- Basic hand tools (socket set) and a jack/stands or ramps for wheel access
- Rags and a safe container to recycle used oil
Having these items on hand helps ensure a proper, leak-free oil change and makes the process more efficient whether you do it at home or at a shop.
DIY oil change steps
If you’re tackling the oil change yourself, follow these general steps to complete the job safely and correctly. Note that you should always refer to the factory manual for torque specs and any model-specific precautions.
- Warm the engine briefly to allow oil to drain more completely, then park on a level surface and engage the parking brake.
- Lift the front of the vehicle and support it securely on jack stands or use ramps.
- Position the oil drain pan beneath the oil pan drain plug.
- Remove the drain plug and allow the used oil to fully drain into the pan.
- While the oil drains, remove the old oil filter and prepare the new filter (lightly oil the gasket to seal properly).
- Install the new oil filter by hand until snug, then follow the filter manufacturer’s instructions for any final tightening.
- Replace the drain plug with a new washer if applicable and tighten to the manufacturer’s specified torque.
- Reinstall the oil filler cap, then slowly add about 6.4 quarts of 0W-20 oil, checking the level with the dipstick as you go to avoid overfill.
- Start the engine and run for a minute, then turn off and check for leaks. Re-check the oil level and add small amounts if needed to reach the full mark.
- Properly dispose of the used oil and filter according to local regulations, and reset the maintenance light if your vehicle uses one.
Following these steps helps ensure a complete and clean oil change, with the correct oil level and a well-sealed filter. If you prefer, a professional shop can perform the service in about the same time with guaranteed results.
Tips and cautions
Always use a secure jack or ramps and never work under a vehicle supported only by a jack. Wear gloves to protect your hands, work in a well-ventilated area, and recycle used oil and filters responsibly. If you’re unsure about torque specs or oil quantities, consult the owner’s manual or a certified mechanic.
Maintenance notes and reminders
Oil change intervals for the 2019 RX 350 typically align with Lexus recommendations based on driving conditions and mileage. In normal conditions, many owners change oil every 5,000 to 7,500 miles with synthetic oil, but always verify your specific maintenance schedule in the owner’s manual. Record the date and mileage of the change to keep track of upcoming service intervals.
Summary
The 2019 Lexus RX 350 generally takes 6.4 quarts (6.1 liters) of 0W-20 synthetic oil when performing an oil change, including the new filter. Whether you do it yourself or have a shop handle it, starting with the right oil, filter, and tools—and following proper steps—will help ensure the engine stays lubricated and healthy. Always consult the owner’s manual for model-specific guidance and adhere to local disposal regulations for used oil.
How much oil does a 3.0 V6 take?
A 3.0L V6 engine typically takes between 4.5 and 6.5 quarts of oil, but the exact amount depends on the specific vehicle make and model. For example, a 2006 Ford Fusion 3.0L V6 requires 6 quarts, while a 2001 Jaguar S-Type 3.0L V6 needs 6.5 quarts. Always check your vehicle's owner's manual for the precise capacity and oil viscosity requirements.
| Vehicle | Oil Capacity |
|---|---|
| 2012 Ford Escape 3.0L V6 | 6 quarts |
| 2006 Ford Fusion 3.0L V6 | 6 quarts |
| 2003 Ford Ranger 3.0L V6 | 4.5 quarts |
| 2001 Jaguar S-Type 3.0L V6 | 6.5 quarts |
(this||self).Wufxzb=function(c,e,f,l,k){var d=document.getElementById(c);if(d&&(d.offsetWidth!==0||d.offsetHeight!==0)){c=d.querySelector("div");var g=c.scrollWidth-c.offsetWidth,h=Math.min(e?g:0,g);c.scrollLeft=e&&(l||f)?0:h;var a=d.getElementsByTagName("g-left-button")[0],b=d.getElementsByTagName("g-right-button")[0];a&&b&&(e=RegExp("\\btHT0l\\b"),f=RegExp("\\bpQXcHc\\b"),a.className=a.className.replace(e,""),b.className=b.className.replace(e,""),h===0?a.className="pQXcHc "+a.className:(a.className=
a.className.replace(f,""),k&&c.classList.add("pA30Ne")),h===g?b.className="pQXcHc "+b.className:(b.className=b.className.replace(f,""),k&&c.classList.add("FpCCub")),setTimeout(function(){a.className+=" tHT0l";b.className+=" tHT0l"},50))}};}).call(this);(function(){var id='_jN8laeSlLcCUxc8Pwqie4Q4_252';var rtl=false;var gecko=false;var edge=false;var soh=false;
(this||self).Wufxzb(id,rtl,gecko,edge,soh);})();
How many quarts of oil does a 3.6 L V6 take?
A 3.6L V6 engine typically takes between 5 and 6 quarts of oil, but the exact amount varies by vehicle model, so you must check your owner's manual or the oil fill cap for the precise capacity. For example, some models like a 2013 Jeep JK require 6 quarts, while newer models like a 2020 Jeep Wrangler or 2018+ Jeep Wrangler JL may only take 5 quarts.
Here are some general guidelines:
- Check your owner's manual: This is the most reliable source for your specific vehicle.
- Look at the oil fill cap: It may have the required viscosity and capacity printed on it.
- Consider the model year: Newer vehicles, especially certain Jeep models, have different oil capacities than older ones.
- Change the oil filter: Always include an oil filter change, as this is part of the full oil capacity.
- After refilling, check the level: After you've filled the engine with oil, use the dipstick to check the oil level and add more if needed to reach the "full" line.
How many quarts of oil does a 3.0 V6 Toyota take?
5 quarts
Pour 5 quarts of 10W-30 automobile oil into the engine. Use one hand to stabilize the funnel to help prevent spills.
How many quarts of oil for a 2019 Lexus RX350?
5.8 quarts
Oil Grade: API*
| Viscosity: | 0W-20 (All TEMPS) - 0W-20 is the best choice for good fuel economy and starting in cold weather. If 0W-20 is not available 5W-20 may be used. However, it must be replaced with 0W-20 at the next oil change. |
|---|---|
| Capacity: | 5.8 quarts (with filter). W/ TT. After refill check oil level. |
