How much oil does a 2.2 transit take?
The Ford Transit 2.2L Duratorq TDCi engine typically requires about 6.0 liters of engine oil for a full change, including the new oil filter. Exact capacity can vary by model year, regional variant, and whether the filter is replaced, so always consult the owner's manual or official Ford service data for your VIN.
In this report, we review the typical capacity figures and provide guidance on verifying the correct oil fill for common 2.2L Transit configurations. The Duratorq 2.2 appears in several Transit generations and regional markets, and minor differences in sump size and filter hardware can shift the total oil requirement by a half-liter or so.
Typical oil capacity for the 2.2L Duratorq engine
These figures reflect commonly stated capacities for the Duratorq 2.2 TDCi used in many Transit variants. Exact numbers depend on variant and whether you replace the filter.
- 6.0 L (about 6.3 quarts) of engine oil when performing a full change that includes a new oil filter, for the most common 2.2L Duratorq TDCi installations in the Transit family.
- Approximately 5.0–5.5 L (about 5.3–5.8 quarts) in some regional or older variant configurations where the sump or filter hardware differs or where a non-standard filter is used.
The bottom line is that 6.0 L is the widely cited guideline for a standard 2.2L Duratorq oil change with filter, but you should confirm against your specific model and service data to avoid under- or overfilling.
Why capacities vary across models
Ford used multiple 2.2L Duratorq iterations across Transits sold in different markets. Differences in sump capacity, oil filter housing, and accessory fittings can change the total oil needed. Always verify via your vehicle’s engine code, VIN, or the official workshop manual for the exact specification.
When in doubt, rely on the dipstick: pour in small increments, recheck, and stop at the midpoint between the MIN and MAX marks once the engine has been running and settled.
How to verify and fill correctly
Before filling, prepare and follow these steps to ensure you reach the correct level.
- Warm up the engine briefly, then switch off and wait several minutes for the oil to drain back into the sump.
- Park on level ground, pull the dipstick, wipe clean, reinsert fully, then pull again to read the current level.
- If performing a full change, replace the oil filter and pour in about the recommended total capacity for your variant (start around 5.5–6.0 L, then adjust).
- Reinsert the dipstick, check level, and add in small increments until the oil level sits between the MIN and MAX marks.
- Run the engine for a few minutes, recheck for leaks, then recheck the level again after the engine rests.
- Dispose of used oil and filter in accordance with local regulations.
Correct oil fill protects engine lubrication and performance, so take your time to verify the final level.
Summary
For most Ford Transit models powered by the 2.2L Duratorq TDCi, plan on about 6.0 liters of engine oil for a full oil change with a new filter. However, exact capacity can vary by engine variant and regional specifications. Always confirm with the official service data for your vehicle, then use the dipstick to verify the final level after filling and running the engine. Regular oil changes with the correct type and quantity help maintain durability and performance.
How many quarts of oil does a 2.2 engine hold?
About 5 1/2 to 6 quarts for engine oil. About 8 gallons of mineral oil or hytran if you have a loader or external hydraulics. Engine holds 6 qt with the filter 5 without. Rear end holds 8 gallons.
How much oil does a 2.2 diesel engine take?
Capacities and Specifications - 2.2L Diesel
| Item | Capacity |
|---|---|
| Engine oil with filter. | 7.68 L |
| Engine oil without filter. | 7.38 L |
| Clutch fluid. | Between the MIN line and the MAX line |
| Manual transmission oil. | 2.6 L |
What kind of oil does a 2.2 diesel take?
SAE 5W-30
Engine oil SAE 5W-301,2.
