How much oil does a 3.5 l V6 Ford Edge take?
The Ford Edge with a 3.5-liter V6 typically takes about 5 quarts of engine oil when performing a standard change, including a new filter. Depending on the exact year and engine variant, some models may use a bit more—up to around 5.5 quarts. Always verify the exact capacity for your vehicle in the owner's manual or a Ford service database.
In this article, we explain the typical oil capacity for the 3.5 L V6 Edge, how capacity can vary by generation and configuration, and how to confirm the correct amount for your specific car. We also cover compatible oil types and practical steps for a proper oil-change procedure.
What engine variants were used in the Ford Edge?
The Edge has used a few versions of the 3.5-liter V6 over its generations. The early models relied on the Duratec 35 configuration, while later models used a Twin Independent Variable Cam Timing (Ti-VCT) variant of the same 3.5-liter family. Capacity can vary slightly by year and whether the engine uses a standard or Ti-VCT setup.
Oil capacity by engine variant
Below is a general guide to the oil capacity for the Edge’s 3.5 L V6 variants. Exact capacity should be confirmed for your year through the owner's manual or Ford's official service data, as it can vary with filters and incidental maintenance.
- 3.5 L Duratec 35 (early Edge models): about 5 quarts (4.7 L) with filter
- 3.5 L Ti-VCT (later Edge models): about 5.0–5.5 quarts (4.7–5.2 L) with filter
These figures reflect typical service fill ranges. If you replace the oil filter or use a different filter size, the capacity may adjust slightly. Always fill to the engine’s exact full mark on the dipstick after completing the change.
Oil type and change procedure
Most 3.5 L V6 Edge engines call for synthetic-blend or full-synthetic 5W-20 oil in many markets, with 5W-30 used in some climates or model years. Always confirm the correct viscosity and spec in your owner’s manual. If you’re unsure, consult a Ford service center or the official Ford parts database for your VIN.
How to verify the exact capacity for your vehicle
Use these steps to confirm you fill to the correct amount for your particular Edge, since capacities can vary slightly by year, trim, and filter choice.
- Check the owner’s manual or the service data for your exact model year and VIN.
- Use the dipstick after an initial fill to see where the level sits between the marks. Add small amounts if needed.
- Run the engine for a few minutes, then recheck the level with the dipstick on a level surface.
- Complete the oil change by replacing the filter and pouring any additional oil needed to reach the FULL mark.
- Record the total oil added for future reference and ensure the level is at the FULL mark when the engine is cool.
Following these steps helps ensure you use the correct amount and avoid overfilling or underfilling, which can impact engine performance and longevity.
Summary
For most Ford Edge 3.5 L V6 engines, the standard oil capacity is around 5 quarts with a filter, with some variants allowing up to roughly 5.5 quarts. Always verify the exact capacity for your specific year and engine variant and use the recommended oil viscosity. Proper filling and regular maintenance help keep the V6 Edge running smoothly.
What oil does a 2013 Ford Edge 3.5 L take?
Full Synthetic Motorcraft Engine Oil Change Kit for 2013 Ford Edge 3.5L V6 5w20.
How much oil does a 3.5 Ford Edge take?
6.0 qt
Capacities and Specifications - 3.5L
| Item | Capacity |
|---|---|
| Engine oil | 6.0 qt (5.7 L) |
| Engine coolant | 11.7 qt (11.1 L) |
| Brake fluid | Between MIN/MAX on brake fluid reservoir |
| Rear differential (All Wheel Drive) fluid | 2.4 pt (1.15L) |
How much oil does a 2012 Ford Edge 3.5 take?
The 2012 Ford Edge 3.5L engine has an oil capacity of 6.0 quarts (5.7 liters) when the filter is changed. It is important to check the dipstick after refilling to ensure the correct level is reached.
- Capacity: 6.0 quarts (5.7 liters) with a filter change.
- Oil Type: The recommended oil is 5W-20.
- Checking the level: After the oil is added, start the engine briefly, then turn it off and wait a few minutes. Check the dipstick and add more oil if necessary to reach the correct level.
How many quarts of oil does a 3.5 L V6 take?
A 3.5L V6 engine typically requires about 6 quarts of oil when changing the filter, although the exact amount can vary slightly by vehicle. Some specific models, like the Toyota Camry, may call for 6.1 quarts, while others like certain Ford F-150s can be closer to 6.3 quarts. Always check your owner's manual for the most accurate capacity for your specific make and model.
How to determine the right amount
- Check your owner's manual: This is the most reliable source for the correct oil capacity for your specific vehicle.
- Consider the filter: The capacity is usually listed for a full oil and filter change. If you are not changing the filter, you will need less oil.
- Measure using the dipstick: After refilling, it's best to start the engine, let it run for a minute, then shut it off and wait a few minutes for the oil to settle. Check the dipstick and add more oil as needed until the level is within the "full" range on the dipstick.
