How much oil does a 4.3 V6 S10 take?
The 4.3L V6 engine in the Chevrolet S10 pickup truck typically requires 4 to 5 quarts of oil for a full oil change. The exact oil capacity can vary slightly depending on the specific model year and other factors, but this is the general range you should expect.
Detailed Answer
The Chevrolet S10 is a compact pickup truck that was produced from 1982 to 2004. Many S10 models were equipped with a 4.3-liter V6 engine, which is the focus of this question.
According to the information gathered from various automotive resources, the oil capacity for a 4.3L V6 engine in the Chevrolet S10 is typically between 4 and 5 quarts. This range accounts for potential variations between different model years, as well as differences in the specific engine configuration or other factors that may impact the total oil capacity.
It's important to always refer to the owner's manual for your specific S10 model to determine the exact oil capacity recommended by the manufacturer. Overfilling or underfilling the engine oil can lead to performance issues or even damage to the engine over time.
Oil Change Procedure
When performing an oil change on a 4.3L V6 S10, follow these general steps:
- Park the vehicle on a level surface and apply the parking brake.
- Locate the oil drain plug, typically located at the bottom of the oil pan, and place a drain pan underneath.
- Unscrew the drain plug and allow the old oil to fully drain from the engine.
- Once drained, replace the drain plug and tighten it securely.
- Locate the oil filter, usually accessible from the top or side of the engine, and remove it using an oil filter wrench.
- Apply a thin coat of new oil to the gasket of the new oil filter, then screw it on until secure.
- Unscrew the oil fill cap and pour in the recommended 4 to 5 quarts of new oil.
- Replace the oil fill cap and start the engine, checking for any leaks.
- Allow the engine to run for a few minutes, then check the oil level using the dipstick and add more oil if necessary.
Be sure to dispose of the old oil and filter properly, and always use the recommended oil type and viscosity for your S10 model.
What kind of oil does a 1988 Chevy s10 4.3 take?
Oil Grade: API*
10W-30 (Above -18°C) - SAE 10W-30 is preferred.
How many miles per gallon does a 4.3 Vortec get?
18 mpg city/24 mpg highway
4.3L V6: 18 mpg city/24 mpg highway (2WD)
What oil goes in a 4.3 V6 engine?
SAE 5W-30
5W-30 (All TEMPS) - SAE 5W-30 is preferred. Capacity: 4.5 quarts (with filter).
How much oil does a 4.3 s10 take?
Oil Grade: API*
| Viscosity: | 10W-30 (Above -18°C) 5W-30 (All TEMPS) - SAE 5W-30 is preferred. |
|---|---|
| Capacity: | 4.5 quarts (with filter). After refill check oil level. |
| Torque: | 18 ft/lbs (Oil Drain Plug) |
How many quarts of oil does a 1997 s10 V6 take?
4.5 quarts
Oil Grade: API*
4.5 quarts (with filter).
How much horsepower does a 1992 4.3 s10 make?
Engine
| Horsepower | 195 hp @ 4,500 rpm |
|---|---|
| Torque | 260 lb-ft @ 3,600 rpm |
How much oil does a 4.3 gmc take?
A 3.0L diesel-equipped GMC Sierra requires 7 quarts of 0w20 dexos2™oil. The 4.3L V6 GMC Sierra takes 6 quarts of 5w30 dexos1™oil. All of the V8-model 2021 GMC Sierra trucks take 8 quarts of 0w20 dexos1™oil.
How many quarts does a 4.3 V6 Chevy take?
Oil Grade: SEOC3
| Viscosity: | 5W-30 (All TEMPS) |
|---|---|
| Capacity: | 6 quarts (with filter). After refill check oil level. |
| Torque: | 18 ft/lbs (Oil Drain Plug) |
How much oil does a 4.3 S10 take?
Capacity: 4.5 quarts (with filter). After refill check oil level.
How much horsepower does a 4.3 L V6 put out?
That'll get you to around 340-350 hp.
