How much oil does a 5.7 Charger RT take?
A 5.7L Hemi-powered Charger RT typically takes about 7 quarts (6.6 liters) of engine oil for a full change with a new filter.
This article explains the official capacity, the recommended oil type, and best practices for checking and topping off oil on a 5.7L Hemi Charger RT. Exact capacity can vary slightly by year, model configuration, and filter choice.
Oil capacity and specifications
The following figures and guidelines apply to the 5.7L Hemi used in Charger RT models. They reflect common service data used by manufacturers and dealers.
Here are the core figures and recommendations to guide an oil change on the 5.7L Hemi in the Charger RT.
- Capacity with filter: 7 quarts (6.6 liters).
- Capacity without filter: roughly 6 quarts (5.7 liters).
- Recommended oil viscosity: SAE 5W-20 for most climates; 5W-30 can be used in hotter environments or as specified by the owner’s manual.
- Oil type: Synthetic or synthetic-blend oil is typical; use a Mopar-approved or equivalent high-quality oil to meet warranty requirements.
- Top-off practice: After an oil change, run the engine, check the level on the dipstick, and add small amounts of oil to reach full.
These figures and practices help ensure you meet the engine's lubrication needs and maintain proper oil pressure and protection.
Oil viscosity and maintenance notes
Use the recommended viscosity listed in your owner’s manual or on the engine oil cap. Most owners follow 5W-20 for daily driving, switching to 5W-30 in hotter climates or for extended service intervals if the manual allows. Always verify the specification for your exact model year and region, and consider an oil life monitor to guide change intervals.
When performing a change, replace the oil filter, secure the drain plug, fill to the full mark, and run the engine briefly to purge air before rechecking the level. If you’re unsure, consult a trusted mechanic or Dodge dealership.
Summary: The 5.7L Hemi engine in the Charger RT typically requires about 7 quarts (6.6 liters) of engine oil for a full change with a filter, commonly 5W-20 synthetic or synthetic blend. Check your manual for exact specifications and follow proper maintenance guidelines.
What oil does a 5.7 V8 Hemi take?
SAE 5W-20
Use the SAE 5W-20 full synthetic oil if your truck has the 5.7L V8 HEMI gasoline engine.
How many quarts of oil for a 5.7 Hemi charger?
A Dodge Charger with a 5.7L Hemi engine requires 7 quarts of oil when replacing the filter. The recommended viscosity is typically SAE 5W-20 for most model years, though you should always confirm the exact type for your specific model year in your owner's manual. After adding the oil, always check the dipstick to ensure the level is correct.
Key details
- Oil capacity: 7 quarts (with filter)
- Recommended oil viscosity: SAE 5W-20 (check owner's manual for your specific model year)
- Action: After adding oil, check the dipstick and add more if needed.
What kind of oil does a Charger RT take?
The oil type for a Dodge Charger RT depends on the specific engine, but for the 5.7L V8 engine, it requires SAE 0W-20 full synthetic oil. For the 6.4L V8 and Supercharged V8 engines, it requires SAE 0W-40 full synthetic oil. Always check your owner's manual to confirm the correct type for your specific model year and engine.
Engine and oil type
- 5.7L V8 (e.g., R/T): SAE 0W-20 full synthetic oil (approximately 7 quarts)
- 6.4L V8 (e.g., Scat Pack): SAE 0W-40 full synthetic oil (approximately 7 quarts)
- 3.6L V6 (e.g., SXT): SAE 5W-20 full synthetic oil (approximately 6 quarts)
Important considerations
- Use full synthetic oil: Mopar recommends full synthetic oil for its better protection against impurities and sludge, and for keeping the engine cleaner for longer.
- Verify with owner's manual: This information is general; always check your owner's manual for the precise oil type, viscosity, and capacity for your specific model year and engine.
- Use the correct oil filter: Using a Mopar or OEM oil filter is recommended to ensure it is made specifically for your model.
- Warm up the engine before changing: When performing an oil change, it's recommended to do it when the engine is warm to ensure the oil flows more easily.
- Check the oil level: After adding the new oil, check the oil level and ensure the car is on a level surface to get an accurate reading.
How many quarts of oil does a 5.7 L V8 take?
The oil capacity for a 5.7L engine, such as the Dodge/Ram Hemi, is 7 quarts with a filter change. After refilling, it's crucial to run the engine to circulate the new oil and then check the dipstick to ensure the level is within the proper range.
- Capacity: 7 quarts (with filter)
- Process:
- Drain the old oil and remove the old filter.
- Lubricate the seal on the new oil filter and install it hand-tight.
- Add 7 quarts of the correct oil to the engine.
- Replace the oil fill cap.
- Start the engine and let it run for a short time to circulate the oil.
- Shut off the engine and check the dipstick to confirm the correct oil level.
