How much oil does a 5.7 L Toyota engine hold?
The 5.7 L Toyota V8 typically holds about 6 quarts (5.7 liters) of engine oil when the filter is included in the capacity.
Oil capacity can vary slightly by model year and whether a replacement oil filter is used, so always confirm with the owner's manual and check the oil level with the dipstick after a change.
Oil capacity specifics for the 5.7 L V8
These figures reflect Toyota's general specification for the 5.7 L i-Force V8 used in trucks like the Tundra and Sequoia. Actual capacity can vary by year, trim, and filter type.
Note: Capacity is typically quoted with the oil filter in place. If the engine has just been drained and a new filter hasn’t been installed yet, the usable oil amount will be less until the filter is added.
- With filter installed: approximately 6.0 quarts (5.7 liters).
- Without filter or when drained for a thorough flush: commonly around 5.0–5.5 quarts (4.7–5.2 liters).
In practice, Toyota’s official guidance centers on 6.0 quarts as the fill volume with the filter in place. Always bring the oil level to the full mark on the dipstick after an oil change and recheck after a brief idle/run.
How to verify the oil level
Use these steps to accurately check the oil level after an oil change or top-up.
- Run the engine briefly, then turn it off and let it sit for 5–10 minutes to allow oil to settle.
- Park on level ground; pull the dipstick, wipe it clean, reinsert fully, and pull it again to read the level.
- If the level is below the full line, add oil in small increments, wait a few minutes, and recheck until it reaches full.
Maintaining the correct oil level protects the engine’s lubrication system and ensures optimal performance.
Summary
For a typical 5.7 L Toyota V8, plan for about 6 quarts (5.7 liters) of engine oil with the filter installed. Capacity can vary slightly by model year and filter, so always consult the owner's manual and confirm the level with the dipstick after servicing.
How many quarts of oil does a 2018 Toyota Tundra with a 5.7 L take?
8.5 quarts
8.5 quarts (with filter). After refill check oil level. Torque: 30 ft/lbs (Oil Drain Plug) Install a new washer on the drain bolt.
How many quarts of oil for a 5.7 L V8?
The oil capacity for a 5.7L engine, such as the Dodge/Ram Hemi, is 7 quarts with a filter change. After refilling, it's crucial to run the engine to circulate the new oil and then check the dipstick to ensure the level is within the proper range.
- Capacity: 7 quarts (with filter)
- Process:
- Drain the old oil and remove the old filter.
- Lubricate the seal on the new oil filter and install it hand-tight.
- Add 7 quarts of the correct oil to the engine.
- Replace the oil fill cap.
- Start the engine and let it run for a short time to circulate the oil.
- Shut off the engine and check the dipstick to confirm the correct oil level.
How many quarts of oil does a 2007 Toyota Tundra 5.7 L take?
The 2007 Toyota Tundra 5.7L engine requires 7.4 quarts of oil with a filter change. Some sources suggest adding up to 7.5 or 7.9 quarts, but it is recommended to start with 7.4 quarts and then check the dipstick, adding more oil only as needed after letting the engine settle. Using an incorrect oil capacity can lead to engine damage, so it is best to check the dipstick and not overfill.
Oil capacity for 2007 Tundra 5.7L
- Initial fill: 7.4 quarts (with filter)
- Final check: Add oil as needed after allowing it to settle for 10 minutes, checking the dipstick to ensure the level is correct and not overfilled.
- Recommended oil: Use 0W-20 viscosity synthetic oil that meets ILSAC GF5 specifications.
How much oil does a 5.7 Toyota V8 take?
8.5 quarts
2018-2021 Toyota Tundra 5.7L V8 oil change fill capacity is 8.0 liters (8.5 quarts). 2010-2017 Toyota Tundra 5.7L V8 oil change fill capacity is 7.5 liters (7.9 quarts).
