How much oil does a Can Am Maverick take?
The engine oil capacity of Can-Am Maverick side-by-sides varies by model and year, but most versions take roughly 2.0 to 2.5 quarts (about 1.9–2.4 liters) during a full oil change with a new filter.
Exact figures depend on the specific model and engine variant. The Maverick X3 uses Rotax engines (900cc or 1000R), and many changes call for around 2.0–2.3 quarts, while smaller Trail/Sport models are typically in the same general range. Always refer to the owner's manual or service manual for your exact machine to confirm the precise amount and the recommended oil type.
Oil capacity by model and engine
BRP engines in Mavericks share a family, but capacity is not identical across every variant. This quick guide provides typical ranges to help you estimate what you need before checking the exact spec for your machine.
- Maverick X3 (Rotax 900/1000R engines): approximately 2.0–2.3 quarts (1.9–2.2 liters) of engine oil with a new filter.
- Maverick Trail/Sport variants: approximately 1.9–2.0 quarts (about 1.8–1.9 liters) with a new filter.
- Dual-seat Maverick Max variants: similar to other X3/Sport lines, typically around 2.0–2.3 quarts (1.9–2.2 liters) with a new filter.
Note: Oil capacity figures can vary by year and whether you’re performing a simple top-up vs. a complete drain-and-fill with filter replacement. Always verify with the exact manual for your serial number.
Oil type and filling procedure
Using the right oil and following a proper fill procedure helps maintain engine reliability. BRP generally recommends a high-quality full-synthetic oil that meets Rotax 4-stroke engine specifications, commonly BRP XPS 5W-40, or an equivalent that meets the Rotax standard. The process below covers a standard full oil change with filter replacement.
Follow these steps to change the oil and fill to the correct level:
- Warm the engine briefly to circulating temperature to help drain oil more completely.
- Place the Maverick on a level surface and disconnect the battery if necessary for safety.
- Remove the drain bolt and drain the old oil into an approved container; remove the oil filter and prepare a new filter.
- Install the new filter, reinstall the drain plug with the proper torque specification, and fill with the correct amount of oil gradually.
- Check the oil level with the dipstick after letting the oil settle for a few minutes; top off in small increments to reach the recommended level.
- Run the engine for a few minutes, recheck level, and look for leaks. Dispose of old oil in accordance with local regulations.
Conclusion: Use the exact capacity figure from your manual, as it depends on your Maverick model/year and whether you are changing the filter. The guidance above provides a practical framework for planning and performing the oil change.
Summary
Key takeaways:
- Most Can-Am Maverick models use about 2.0–2.5 quarts (1.9–2.4 L) of engine oil per full change with a new filter.
- The precise figure varies by model and year; consult the owner's manual for your machine’s exact specification.
- Use a high-quality synthetic oil that meets Rotax specifications, typically 5W-40, such as BRP XPS 5W-40.
How much oil does a Can Am Maverick hold?
Book says up to 3.5qts.
How much oil does a 4.0 inline 6 take?
6 quarts (with filter).
What oil does a Can Am Maverick 1000R take?
The Can-Am Maverick 1000R requires SAE 5W-40 or 10W-40 synthetic oil for the engine, depending on the climate, and SAE 75W-90 gear oil for the front and rear differentials. For colder climates, 5W-40 is recommended, while hotter climates may benefit from a higher viscosity like 10W-50.
Engine oil
- Viscosity: Use SAE 5W-40 or 10W-40 full synthetic ATV/UTV motor oil.
- Climate recommendation:
- Colder climates: Use SAE 5W-40.
- Hotter climates: Use SAE 10W-50.
- Special note: Always ensure the oil is wet-clutch compatible and designed for powersports engines.
Differential oil
- Viscosity: Use SAE 75W-90 gear oil.
- Purpose: This oil is specifically designed for the front and rear differentials to ensure proper lubrication and protection.
How much oil does a 2018 Can Am Maverick x3 Turbo R take?
To change the engine oil, you'll need 4 quarts of XPS 10w-50 full synthetic, a new Can-Am oil filter element, a new O-ring for the filter housing, and two new crush washers for the drain bolts.
