How much oil for brz oil change?
The current BRZ with the 2.4-liter FA24D engine requires about 5.7 quarts (5.4 liters) of engine oil when you perform an oil change with a new filter.
This article explains the exact quantity, the recommended oil type, and practical steps to ensure a proper, reliable oil change for the BRZ.
Official oil capacity for the BRZ
The following guidance applies to the FA24D-powered BRZ (2022–present). The oil capacity is listed with a new filter installed.
- Oil capacity including the filter: 5.7 quarts (5.4 liters).
- Recommended oil viscosity: 0W-20 synthetic oil, API SN or newer; always follow the specification in your owner's manual for your climate and region.
- Notes: Some markets or service centers may quote a range around 5.5–5.7 quarts depending on the filter and oil brand; after adding oil, run the engine briefly, then check the dipstick and adjust to the full line.
In practice, plan to add roughly 5.7 quarts, then verify the level with the dipstick once the oil has settled. Small differences can occur due to filter fill and drainage from the sump.
What you’ll need for a BRZ oil change
Having the correct oil quantity, filter, and tools on hand helps ensure a clean, accurate change.
- 5.7 quarts (5.4 liters) of 0W-20 synthetic oil, or the specification listed in your owner's manual.
- One FA24D-compatible engine oil filter.
- New drain plug washer, oil drain pan, a funnel, and a suitable socket for the drain bolt.
- Oil filter wrench, rags, gloves, and safe lifting equipment (jack stands or ramps) to access the underside of the car.
When you complete the change, follow the vehicle's procedures for checking oil level and verify the reading on the dipstick after the engine has run and the oil has settled.
Model-year scope
The figures above apply to the current BRZ (2022–present) powered by the FA24D 2.4L engine. Earlier BRZ models used the 2.0L FA20 engine with a different oil capacity, typically around 4.8–5.0 quarts depending on the filter. Always confirm the exact specification for your vehicle’s year and market in the owner's manual or with an authorized dealer.
Summary
For the modern BRZ with the 2.4L FA24D engine, you should plan on about 5.7 quarts (5.4 liters) of engine oil when performing an oil change with a new filter. Use 0W-20 synthetic oil as recommended, fill carefully, and recheck the level after the oil has settled. This approach helps ensure proper lubrication and accurate oil level readings across driving conditions.
How much oil does a 2018 brz take?
5.7 quarts
A 2018 Subaru BRZ takes 5.7 quarts of oil. How much oil you should use depends considerably on the type of car, engine size, and type of oil.
Is 4 quarts enough for an oil change?
Typically, engines need five to eight quarts of oil. However, the size of your engine can impact how much oil is required. For example, a 4-cylinder oil engine may require around five quarts of oil, whereas a 6-cylinder oil needs six quarts. Usually, the smaller the engine is, the less oil you'll need for your vehicle.
How many quarts of oil does a brz take?
The oil capacity for a Subaru BRZ depends on the model year, but common capacities are around 5.7 quarts with a filter for older 2.0L engines and 5.3 quarts with a filter for newer 2.4L engines. Always check the vehicle's owner's manual or the oil dipstick to confirm the exact capacity and level after refilling.
Oil capacity by model year
- 2.0L Engine (e.g., 2013-2020): Approximately 5.7 quarts with a new oil filter.
- 2.4L Engine (e.g., 2023+): Approximately 5.3 quarts with a new oil filter.
Important considerations
- After refilling: Always check the oil level with the dipstick after adding the new oil and after running the engine briefly to ensure it's at the correct level. Some owners report that the recommended 5.3 quarts can be slightly short, and an additional half-quart may be needed to reach the full mark, so it's best to add slowly and check the level.
- Oil filter: The specified capacity typically includes the oil filter, so it should be changed at the same time as the oil for an accurate measurement.
- Torque: The oil drain plug should be tightened to 31 ft-lbs for 2016 and 2023 models, and a new washer should be used.
- Oil type: The recommended viscosity for both engines is 0W-20 synthetic oil.
How many quarts of oil does a 3.0 L V6 take?
A 3.0L V6 engine typically takes between 4.5 and 6.5 quarts of oil, but the exact amount depends on the specific vehicle make and model. For example, a 2006 Ford Fusion 3.0L V6 requires 6 quarts, while a 2001 Jaguar S-Type 3.0L V6 needs 6.5 quarts. Always check your vehicle's owner's manual for the precise capacity and oil viscosity requirements.
| Vehicle | Oil Capacity |
|---|---|
| 2012 Ford Escape 3.0L V6 | 6 quarts |
| 2006 Ford Fusion 3.0L V6 | 6 quarts |
| 2003 Ford Ranger 3.0L V6 | 4.5 quarts |
| 2001 Jaguar S-Type 3.0L V6 | 6.5 quarts |
(this||self).Wufxzb=function(c,e,f,l,k){var d=document.getElementById(c);if(d&&(d.offsetWidth!==0||d.offsetHeight!==0)){c=d.querySelector("div");var g=c.scrollWidth-c.offsetWidth,h=Math.min(e?g:0,g);c.scrollLeft=e&&(l||f)?0:h;var a=d.getElementsByTagName("g-left-button")[0],b=d.getElementsByTagName("g-right-button")[0];a&&b&&(e=RegExp("\\btHT0l\\b"),f=RegExp("\\bpQXcHc\\b"),a.className=a.className.replace(e,""),b.className=b.className.replace(e,""),h===0?a.className="pQXcHc "+a.className:(a.className=
a.className.replace(f,""),k&&c.classList.add("pA30Ne")),h===g?b.className="pQXcHc "+b.className:(b.className=b.className.replace(f,""),k&&c.classList.add("FpCCub")),setTimeout(function(){a.className+=" tHT0l";b.className+=" tHT0l"},50))}};}).call(this);(function(){var id='_-d8laZfBMci49u8P7rTuqAI_153';var rtl=false;var gecko=false;var edge=false;var soh=false;
(this||self).Wufxzb(id,rtl,gecko,edge,soh);})();
