How much oil goes in a 3.7 L V6?
A typical 3.7 L V6 engine requires about 6 quarts (5.7 liters) of engine oil when changing the oil with a new filter. Exact capacity varies by model year and variant, so check your owner's manual for the precise figure.
Understanding the 3.7 L V6 oil capacity
The 3.7 L V6 is used in several Ford models and other applications, with subtle differences in oil pan design and filter size. While the standard oil change fill is around six quarts, the precise amount depends on the specific engine version, whether you replace the filter, and the vehicle’s year. Always rely on VIN-specific specifications from the owner’s manual or a dealership service data sheet.
Why capacity can vary
Small variations in the oil pan capacity, the oil filter size, and the way the engine was configured for a given model year can affect the total oil needed. Manufacturers publish exact figures for each variant, so a quick check of the official specification for your exact vehicle is the safest approach.
Typical capacity and how to verify
Below is a common benchmark used for many 3.7 L V6 configurations. The precise figure for your car should come from official documentation.
- 6 quarts (about 5.7 liters) of engine oil is commonly cited for a full oil change with a new filter on many 3.7 L Ti-VCT V6 engines.
Conclusion: Always confirm the exact quantity for your specific vehicle variant, year, and filter choice via the owner's manual or dealer service data, as there can be small differences.
Practical steps for performing an oil change and reaching the correct fill
If you’re performing an oil change, follow these typical steps to reach the correct fill level and avoid overfilling.
- Warm the engine to operating temperature, then park on level ground and turn off the engine.
- Place a drain pan under the oil drain plug, remove the plug, and let the old oil drain completely.
- Remove and replace the oil filter with a new one of the correct specification for your engine, if performing a filter change.
- Reinstall the drain plug and wipe away any residue.
- Using a funnel, add oil gradually. For a typical 3.7 L V6, plan on around 6 quarts total, but refer to the exact spec for your vehicle and adjust as needed.
- Run the engine for a minute to circulate the new oil, then turn off and wait a few minutes for the oil to settle.
- Check the oil level with the dipstick and top up in small increments until the level is within the Full range on the dipstick.
- Reinstall the dipstick and oil filler cap, then record the service and dispose of used oil responsibly.
Conclusion: After following these steps and checking the dipstick, your oil should be at or near the recommended level for your specific engine configuration. If in doubt, recheck after a short drive and a level surface.
Where to find the exact capacity for your vehicle
Because the 3.7 L V6 appears in multiple models across different years, the most reliable source is your vehicle’s official documentation or a dealer. Look up:
- Your owner's manual: oil capacity and recommended oil grade.
- Under-hood label near the oil fill cap (some models list capacity there).
- The manufacturer's service information for your VIN (Ford’s official site or dealer portal).
- Trusted automotive resources or your service technician for year-specific figures.
Conclusion: Always verify the exact capacity for your VIN, as small differences in variant or filter size can affect the precise amount required.
Summary
For a typical 3.7 L V6, expect about 6 quarts (5.7 liters) of engine oil during an oil change with a new filter. Confirm the exact capacity for your specific model year and variant using the owner's manual or dealer service data, and follow proper procedure to ensure a correct fill and optimal engine protection.
What kind of oil does a 2004 Jeep Liberty 3.7 L take?
The 2004 Jeep Liberty with the 3.7L engine requires SAE 5W-30 motor oil. The vehicle holds approximately 5 quarts of oil and a filter change is recommended at each oil change. You can use conventional, synthetic blend, or full synthetic oil, with a high-mileage version being a good option for vehicles with more than 75,000 miles.
Key details
- Oil Type: SAE 5W-30
- Capacity: 5 quarts (with filter)
- Filter: Replace the oil filter at every oil change
- Synthetic vs. Conventional: A high-mileage full synthetic oil is recommended for engines over 75,000 miles.
Important note
- For temperatures below -18∘Cnegative 18 raised to the composed with power cap C−18∘𝐶 (-0.4∘Fnegative 0.4 raised to the composed with power cap F−0.4∘𝐹), SAE 5W-30 is the preferred viscosity. The 10W-30 viscosity is only suitable for temperatures above -18∘Cnegative 18 raised to the composed with power cap C−18∘𝐶.
What kind of oil does a 2014 f150 3.7 take?
The correct oil for a 2014 Ford F-150 with a 3.7L engine is SAE 5W-20. You can use a synthetic blend or full synthetic oil, but it's crucial to check the owner's manual or the oil filler cap for the exact specifications and any required industry certifications to ensure you use the correct product.
Key details for your 2014 F-150 3.7L oil change
- Oil Viscosity: SAE 5W-20
- Oil Type: Synthetic blend or full synthetic are both acceptable. Look for oil that meets the specified Ford specifications, such as WSS-M2C945-A.
- Oil Capacity: The engine oil capacity is approximately 6 quarts with a filter change, but always verify the level with the dipstick after refilling.
- Where to find oil information: The owner's manual or the oil filler cap on the engine will have the most accurate information for your specific vehicle.
How much oil does a 3.7 V6 take?
6.0 qt
Capacities and Specifications - 3.7L
| Item | Capacity |
|---|---|
| Engine oil (with oil filter) | 6.0 qt (5.7 L) |
| Engine coolant | 11.7 qt (11.1 L) |
| Brake fluid | Between MIN/MAX on brake fluid reservoir |
| Rear differential fluid (All Wheel Drive) | 2.4 pt (1.15L) |
How many quarts of oil does a 2012 F150 3.7 take?
The oil capacity for a 2012 Ford F-150 with a 3.7L engine is 6 quarts (5.7 liters) with a filter change. It is recommended to use SAE 5W-20 motor oil for this engine.
- Capacity: 6 quarts (5.7 liters)
- Oil type: SAE 5W-20
