How much transmission fluid does a 2004 Ford Focus take?
For the 2004 Ford Focus, automatic transmissions typically take about 7–9 quarts of ATF, while the manual MTX-75 uses roughly 2 quarts of gear oil. The exact amount depends on the specific transmission in your car and whether you’re performing a full drain-and-fill (with a pan gasket and filter) or just a simple top-up.
Automatic transmission capacity (4-speed automatic)
If your Focus is equipped with the 4-speed automatic, here is a practical quick reference for service work.
- Total system capacity (including the torque converter): about 7–9 quarts.
- Refill amount after a pan drain and filter change: about 6–7 quarts.
- Recommended fluid type: Ford Mercon V (confirm the exact specification in your owner’s manual or service manual).
When performing a full system drain and fill, prepare to add roughly 6 to 7 quarts to reach the proper level, and have extra on hand in case a second top-off is needed after the transmission cycles.
Manual transmission capacity (MTX-75)
For the 5-speed manual option, the capacity is considerably smaller and straightforward to manage during a pan fill.
- Approximate fill capacity: about 1.9–2.2 quarts.
- Fluid type: gear oil, typically 75W-90 GL-4/GL-5 (check the owner's manual for the precise specification).
When topping up or replacing the manual transmission oil, measure carefully to avoid overfilling, and use the recommended viscosity and spec as noted in Ford’s documentation for your vehicle.
Notes and maintenance tips
Always verify the exact specification using your VIN and the vehicle’s manual, as regional variations or different market versions of the Focus can have different requirements. If you’re unsure, consult a Ford dealer or a trusted service manual for your exact transmission code (for example, AX4S/MTX-75) to confirm capacities and fluid type before draining.
Summary
In short, a 2004 Ford Focus with an automatic transmission typically requires 7–9 quarts of ATF, while the manual MTX-75 needs around 2 quarts of gear oil. Perform a full drain-and-fill with a replacement filter for the most accurate results, and always verify the precise specification for your car based on its transmission code and country of sale.
How many quarts of transmission fluid does a Ford Focus take?
Out. It's going to hold just under two quarts of fluid. So you'll pull that plug out. Anyway. If I guess you could do it without doing it you could measure the amount of fluid that comes out of it.
What kind of transmission fluid does a 2004 Ford Focus take?
The 2004 Ford Focus uses Mercon LV for automatic transmissions or a high-quality, full synthetic manual transmission fluid with a SAE 75W-90 grade for manual transmissions. It is recommended to consult your owner's manual for the exact specifications, as there can be variations depending on the transmission type and specific engine.
Automatic transmission
- Fluid type: Mercon LV (full synthetic).
- Why it's important: The transmission fluid lubricates, cools, and acts as a hydraulic fluid for shifting. Using the correct type is vital for smooth performance and longevity.
Manual transmission
- Fluid type: A full synthetic, manual transmission fluid with an SAE 75W-90 grade is recommended. For the 2.0L engine, the Ford part number is XT-M5-QS.
- Capacity: The 2.3L engine with an MTX-75 transmission holds 4 pints, and the level should be no higher than 3/83 / 83/8 inch below the fill hole.
How to choose the right fluid
- Check your owner's manual: This is the most reliable source for determining the correct fluid type for your specific vehicle.
- Look for matching specifications: When buying fluid, match the specifications listed in your owner's manual, such as Mercon LV or SAE 75W-90.
- Consider manufacturer part numbers: For manual transmissions, the manufacturer's part number can help ensure compatibility.
How many quarts does a 2004 Ford Focus take?
4.5 quarts
Oil Grade: SEO60
| Viscosity: | 5W-30 (All TEMPS) |
|---|---|
| Capacity: | 4.5 quarts (with filter). After refill check oil level. |
| Torque: | 18 ft/lbs (Oil Drain Plug) |
How many quarts of transmission fluid for a drain and fill?
For a standard transmission fluid drain and fill, you'll typically need 3 to 5 quarts, but you should always measure the amount you drained and refill with the same amount to start, then check the level using the dipstick after running the engine. The exact amount varies by vehicle, and it's crucial to check the owner's manual or look up specifications for your specific make and model, as a drain and fill will not replace all the old fluid.
How to determine the right amount
- Drain the old fluid: Let the old fluid drain completely.
- Measure the drained fluid: Measure how much fluid was drained. This is your starting point for refilling.
- Refill with the measured amount: Put the same amount of new, correct transmission fluid back into the transmission. Using a funnel can help with this process.
- Start the engine: Start the vehicle and let it run for a few minutes, shifting through all the gears (Park, Reverse, Neutral, Drive) while holding the brake. This circulates the new fluid.
- Check the level: Turn the engine off and check the fluid level with the dipstick. Add more fluid in small increments if the level is low, or drain a small amount if it's too high.
- Re-check: Repeat the process of running the engine and checking the dipstick until the fluid level is correct according to the dipstick's hash marks for a "hot" reading.
Important considerations
- A drain and fill is different from a full transmission flush, which requires significantly more fluid (10-12 quarts or more) because it aims to replace all the fluid, including what's in the torque converter.
- You should always use the specific type of transmission fluid recommended by your vehicle's manufacturer to avoid damage.
- Some vehicles, like certain Land Rovers, do not have a dipstick and require a fluid extractor to add new fluid. Consult your owner's manual to be certain.
